- 您現在的位置：買賣IC網 > PDF目錄376214 > MXC6202M (Electronic Theatre Controls, Inc.) Low Power, Low Profile 【2 g Dual Axis Accelerometer with I2C Interface PDF資料下載
參數資料
| 型號： | MXC6202M |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Low Power, Low Profile 【2 g Dual Axis Accelerometer with I2C Interface |
| 中文描述： | 低功耗，低簡介【2克雙軸加速度計I2C接口 |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 313K |
| 代理商： | MXC6202M |
Fourth cycle: Master device sends a START command
followed by calling Memsic device address with a WRITE
(8
th
SCL, SDA keep low). An “acknowledge” should be
sent by Memsic device at the end.
Fifth cycle: Master device writes to Memsic device a
“[00000000]” as the starting address for which internal
memory is to be read. Since “[00000000]” is the address of
internal control register, reading from this address can serve
as a verification of operation and to confirm the write
command has been successful. Note: the starting address in
principle can be any of the 5 addresses. For example, user
can start read from address [0000001], which is X channel
MSB.
Sixth cycle: Master device calls Memsic device address
with a READ (8
th
SCL cycle SDA line high). Memsic
device should acknowledge at the end.
Seventh cycle: Master device cycles SCL line, first
addressed memory data appears on SDA line. If in step 7,
“[00000000]”
was sent, internal control register data
should appear (in the following steps, this case is assumed).
Master device should send acknowledge at the end.
LCC-8 PACKAGE DRAWING
MEMSIC MXC6202G/H/M/N
Rev.B
Page 10 of 10
11
/10/2005
Eighth cycle: Master device continues cycle SCL line, next
byte of internal memory should appear on SDA line (MSB
of X channel). The internal memory address pointer
automatically
moves
to
acknowledges.
Ninth cycle: LSB of X channel. In the case that TOEN bit
of internal register was set to “1”, the MSB and LSB of
TOUT (temperature) should appear in last two steps.
Tenth cycle: MSB of Y channel.
Eleventh cycle: LSB of Y channel.
Master ends communications by sending NO acknowledge
and followed by a STOP command. Note: if mater device
continues to cycle SCL line, the memory pointer will go to
sixth and seventh positions, which always have
“[00000000]”. After seventh position, pointer will go to
zero again.
Optional: Master powers down Memsic device by writing
into internal control register. (See step 1 through 4 for
WRITE operation)
the
next
byte.
Master
Hermetically Sealed Package Outline
相關PDF資料 |
PDF描述 |
|---|---|
| MXC6202N | Low Power, Low Profile 【2 g Dual Axis Accelerometer with I2C Interface |
| MXC6202XJ | Ultra Low Cost, 【2.0 g Dual Axis Accelerometer With I2C Interface |
| MXC6202XK | Ultra Low Cost, 【2.0 g Dual Axis Accelerometer With I2C Interface |
| MXD2002A | Low Cost, 【10 g Dual Axis Accelerometer with Digital Outputs |
| MXD2002B | Low Cost, 【10 g Dual Axis Accelerometer with Digital Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MXC6202MP | 制造商:MEMSIC 功能描述:ACCELEROMETER 2AXIS +/-2G 8LCC 制造商:MEMSIC 功能描述:ACCELEROMETER, 2AXIS, +/-2G, 8LCC 制造商:MEMSIC 功能描述:ACCELEROMETER, 2AXIS, +/-2G, 8LCC; Acceleration Range: 2g; Supply Voltage Min:2.7V; Supply Voltage Max:3.6V; Sensor Case Style:LCC; No. of Pins:8; SVHC:No SVHC (19-Dec-2012); Interface Type:I2C; Operating Temperature Max:85C; ;RoHS Compliant: Yes |
| MXC6202N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Power, Low Profile ±2 g Dual Axis Accelerometer with I2C Interface |
| MXC6202XJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ultra Low Cost, ±2.0 g Dual Axis Accelerometer With I2C Interface |
| MXC6202XK | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ultra Low Cost, ±2.0 g Dual Axis Accelerometer With I2C Interface |
| MXC6225XC (DTOS WLP) | 制造商:MEMSIC INC 功能描述:IC ACCELEROMETER XY AXIS 6CSP |
發布緊急采購，3分鐘左右您將得到回復。