- 您現在的位置：買賣IC網 > PDF目錄11671 > MXB7846EUE+ (Maxim Integrated Products)IC CNTRLR TOUCH RES 16TSSOP PDF資料下載
參數資料
| 型號： | MXB7846EUE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/24頁 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR TOUCH RES 16TSSOP |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 96 |
| 類型： | 溫度傳感器 |
| 輸入類型： | 模擬 |
| 輸出類型： | 數字 |
| 接口： | 4 線 |
| 電流 - 電源： | 950µA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
MXB7846
2.375V to 5.25V, 4-Wire Touch-Screen Controller
with Internal Reference and Temperature Sensor
______________________________________________________________________________________
19
Hardware Power-Down
CS also places the MXB7846 into power-down. When
CS goes HIGH, the MXB7846 immediately powers
down and aborts the current conversion. The internal
reference does not turn off when
CS goes high. To dis-
able the internal reference, an additional command
byte is required before
CS goes high (PD1 = 0). Set
PD1 = 0 before
CS goes high.
Touch-Screen Settling
There are two key touch-screen characteristics that can
degrade accuracy. First, the parasitic capacitance
between the top and bottom layers of the touch screen
can result in electrical ringing. Second, vibration of the
top layer of the touch screen can cause mechanical
contact bouncing.
External filter capacitors may be required across the
touch screen to filter noise induced by the LCD panel
or backlight circuitry, etc. These capacitors lengthen
the settling time required when the panel is touched
and can result in a gain error, as the input signal may
not settle to its final steady-state value before the ADC
samples the inputs. Two methods to minimize or elimi-
nate this issue are described below.
One option is to lengthen the acquisition time by stopping
or slowing down DCLK, allowing for the required touch-
screen settling time. This method solves the settling time
problem for both single-ended and differential modes.
The second option is to operate the MXB7846 in the dif-
ferential mode only for the touch screen, and perform
additional conversions with the same address until the
input signal settles. The MXB7846 can then be placed
in the power-down state on the last measurement.
Connection to Standard Interface
MICROWIRE Interface
When using the MICROWIRE- (Figure 13) or SPI-com-
patible interface (Figure 14), set the CPOL = CPHA = 0.
Two consecutive 8-bit readings are necessary to obtain
the entire 12-bit result from the ADC. DOUT data transi-
tions occur on the serial clock’s falling edge and are
clocked into the P on the DCLK’s rising edge. The first
8-bit data stream contains the first 8 bits of the current
conversion, starting with the MSB. The second 8-bit
data stream contains the remaining 4 result bits fol-
lowed by 4 trailing zeros. DOUT then goes high imped-
ance when
CS goes high.
QSPI/SPI Interface
The MXB7846 can be used with the QSPI/SPI interface
using the circuit in Figure 14 with CPOL = 0 and CPHA
= 0. This interface can be programmed to do a conver-
sion on any analog input of the MXB7846.
TMS320LC3x Interface
Figure 15 shows an example circuit to interface the
MXB7846 to the TMS320. The timing diagram for this
interface circuit is shown in Figure 16.
Use the following steps to initiate a conversion in the
MXB7846 and to read the results:
1) The TMS320 should be configured with CLKX (trans-
mit clock) as an active-high output clock and CLKR
(TMS320 receive clock) as an active-high input
clock. CLKX and CLKR on the TMS320 are connect-
ed to the MXB7846 DCLK input.
MICROWIRE
I/O
SCK
MOSI
MASKABLE
INTERRUPT
MISO
CS
DCLK
DIN
BUSY
DOUT
MXB7846
Figure 13. MICROWIRE Interface
QSPI/SPI
I/O
SCK
MOSI
MASKABLE
INTERRUPT
MISO
CS
DCLK
DIN
BUSY
DOUT
MXB7846
Figure 14. QSPI/SPI Interface
TMS320LC3x
XF
CLKX
DR
DX
FSR
CLKR
CS
SCLK
DIN
BUSY
DOUT
MXB7846
Figure 15. TMS320 Serial Interface
相關PDF資料 |
PDF描述 |
|---|---|
| 2081202-3 | CONN PLUG SMA CRIMP RG174 |
| MXB7846EEE+ | IC CNTRLR TOUCH RES 16QSOP |
| MAX6682MUA+ | IC THERMISTOR TO DGTL 8UMAX |
| VI-BTK-IW-F3 | CONVERTER MOD DC/DC 40V 100W |
| VI-BTJ-IX-F2 | CONVERTER MOD DC/DC 36V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MXB7846EUE+ | 功能描述:觸摸屏轉換器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MXB7846EUE+T | 功能描述:觸摸屏轉換器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MXB7846EUE-T | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MXB7846EVC16 | 功能描述:數據轉換 IC 開發工具 MXB7846C16 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MXB7846EVKIT | 功能描述:開發板和工具包 - 其他處理器 Programmers, Development Systems RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。