- 您現在的位置：買賣IC網 > PDF目錄98049 > MUN5230T3 (MOTOROLA INC) 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR PDF資料下載
參數資料
| 型號： | MUN5230T3 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 小信號晶體管 |
| 英文描述： | 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| 封裝： | SC-70, 3 PIN |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 172K |
| 代理商： | MUN5230T3 |
MUN5211T1 SERIES
http://onsemi.com
9
MINIMUM RECOMMENDED FOOTPRINTS FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the
total design. The footprint for the semiconductor packages
must be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
mm
inches
0.035
0.9
0.075
0.7
1.9
0.028
0.65
0.025
0.65
0.025
SC–70/SOT–323 POWER DISSIPATION
The power dissipation of the SC–70/SOT–323 is a
function of the pad size. This can vary from the minimum
pad size for soldering to the pad size given for maximum
power dissipation. Power dissipation for a surface mount
device is determined by TJ(max), the maximum rated
junction temperature of the die, RθJA, the thermal
resistance from the device junction to ambient; and the
operating temperature, TA. Using the values provided on
the data sheet, PD can be calculated as follows:
PD =
TJ(max) – TA
RθJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values
into the equation for an ambient temperature TA of 25°C,
one can calculate the power dissipation of the device which
in this case is 150 milliwatts.
PD =
150
°C – 25°C
= 150 milliwatts
833
°C/W
The 833
°C/W assumes the use of the recommended
footprint on a glass epoxy printed circuit board to achieve a
power dissipation of 150 milliwatts. Another alternative
would be to use a ceramic substrate or an aluminum core
board such as Thermal Clad
. Using a board material such
as Thermal Clad, a power dissipation of 300 milliwatts can
be achieved using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within
a short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference should be a maximum of 10
°C.
The soldering temperature and time should not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5
°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied
during cooling
* Soldering a device without preheating can cause
excessive thermal shock and stress which can result in
damage to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| MUN5233T3 | 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| MUN5214T3 | 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| MUN5215T3 | 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| MUN5235T3 | 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| MUN5235T1 | 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MUN5231 | 制造商:WEITRON 制造商全稱:Weitron Technology 功能描述:NPN Silicon Bias Resistor Transistor |
| MUN5231DW | 制造商:WEITRON 制造商全稱:Weitron Technology 功能描述:Surface Mount Dual Bias Resistor Transistor |
| MUN5231DW1 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual NPN Bias Resistor Transistors R1 = 2.2 k, R2 = 2.2 k |
| MUN5231DW1T1 | 功能描述:開關晶體管 - 偏壓電阻器 100mA 50V BRT NPN RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
| MUN5231DW1T1G | 功能描述:開關晶體管 - 偏壓電阻器 100mA 50V BRT NPN RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。