- 您現在的位置：買賣IC網 > PDF目錄369934 > MUN2134RT1 (樂山無線電股份有限公司) Bias Resistor Transistor PDF資料下載
參數資料
| 型號： | MUN2134RT1 |
| 廠商： | 樂山無線電股份有限公司 |
| 英文描述： | Bias Resistor Transistor |
| 中文描述： | 偏置電阻晶體管 |
| 文件頁數： | 9/10頁 |
| 文件大小： | 236K |
| 代理商： | MUN2134RT1 |
9
Motorola Small–Signal Transistors, FETs and Diodes Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the SC–59 package should be
the same as the pad size on the printed circuit board, i.e., a
1:1 registration.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 23 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177–189
°
C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
170
°
C
140
°
C
Figure 23. Typical Solder Heating Profile
相關PDF資料 |
PDF描述 |
|---|---|
| MUN2115RT1 | Bias Resistor Transistor |
| MUN2116RT1 | Bias Resistor Transistor |
| MUN2112RT1 | Bias Resistor Transistor |
| MUN2113RT1 | Bias Resistor Transistor |
| MUN2132RT1 | Bias Resistor Transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MUN2134T1 | 功能描述:開關晶體管 - 偏壓電阻器 100mA 50V BRT PNP RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
| MUN2134T1G | 功能描述:開關晶體管 - 偏壓電阻器 100mA 50V BRT PNP RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
| MUN2135T1G | 制造商:ON Semiconductor 功能描述:PNP DIGITAL TRANSISTOR (B - Tape and Reel 制造商:ON Semiconductor 功能描述:PNP DIGITAL TRANSISTOR (B - Cut TR (SOS) 制造商:ON Semiconductor 功能描述:REEL / PNP DIGITAL TRANSISTOR (B |
| MUN2136 | 制造商:WEITRON 制造商全稱:Weitron Technology 功能描述:Bias Resistor Transistor PNP Silicon |
| MUN2136T1 | 功能描述:TRANS BRT PNP 100MA 50V SC59 RoHS:否 類別:分離式半導體產品 >> 晶體管(BJT) - 單路﹐預偏壓式 系列:- 標準包裝:10,000 系列:- 晶體管類型:NPN - 預偏壓 電流 - 集電極 (Ic)（最大）:100mA 電壓 - 集電極發射極擊穿（最大）:50V 電阻器 - 基極 (R1)（歐）:47k 電阻器 - 發射極 (R2)（歐）:47k 在某 Ic、Vce 時的最小直流電流增益 (hFE):70 @ 5mA，5V Ib、Ic條件下的Vce飽和度（最大）:300mV @ 500µA，10mA 電流 - 集電極截止（最大）:- 頻率 - 轉換:100MHz 功率 - 最大:250mW 安裝類型:表面貼裝 封裝/外殼:SC-70，SOT-323 供應商設備封裝:PG-SOT323-3 包裝:帶卷 (TR) 其它名稱:SP000756242 |
發布緊急采購，3分鐘左右您將得到回復。