- 您現在的位置：買賣IC網 > PDF目錄45594 > MUAC4K64-90TDI SPECIALTY MICROPROCESSOR CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | MUAC4K64-90TDI |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 29/32頁 |
| 文件大?。?/td> | 504K |
| 代理商： | MUAC4K64-90TDI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁
MUAC Routing CoProcessor (RCP) Family
Pin Descriptions
6
Rev. 4
/FF (Full Flag, Output)
The /FF output indicates when all the memory locations
have their Validity bits set valid (LOW). When there is at
least one location with its Validity bit set HIGH, the /FF
output will be HIGH; when all locations have their
Validity bits set LOW, and the /FI input is LOW, the /FF
output will be LOW. If the /FI input is HIGH, the /FF
output will be HIGH. The state of the /FF line will not
change until after the rising edge of /E during a Write
cycle.
/FI (Full Input, Input)
The /FI input receives full information from the next
higher-priority MUAC RCP in a vertically cascaded
system to provide system-level full information. When the
/FI input is LOW the /FF output will be HIGH if there is at
least one location whose Validity bit is set invalid; when
all locations have their Validity bits set valid, the /FF
output goes LOW. When the /FI input is HIGH, the /FF
output will remain HIGH. The /FF output from one device
is connected to the /FI input of the next lower-priority
device to give system-full indication. The /FI pin of the
highest-priority device must be tied LOW.
/MM (Multiple Match, Open Drain Output)
The /MM line indicates that there is a multiple match
within the system. When the /MI input is HIGH, the /MM
line is pulled LOW if there are at least two matches within
the MUAC RCP as a result of the previous Comparison
cycle; when there are less than two matches, the /MM line
floats HIGH. When the /MI input is LOW, the /MM line is
pulled LOW if there are one or more matches within the
MUAC RCP as a result of the previous Comparison cycle;
when there are no matches, the /MM line floats HIGH.
The /MM lines have open-drain outputs, so all /MM lines
within the system are connected together to give
system-level multiple match indication. The state of the
/MM line will not change until after the rising edge of /E
during a Comparison cycle.
/RESET
The /RESET input is used to reset the MUAC RCP to a
known state. When the /RESET line is pulled LOW it
causes the MUAC RCP to enter its reset state. After power
is applied to the MUAC RCP, the /RESET line must be
held LOW for a time equal to or greater than the minimum
RESET pulse width before the device can operate
correctly. This pin is internally pulled up.
TCLK (JTAG Test Clock, Input)
The TCLK input is the Test Clock input. This pin is
internally pulled up.
TMS (JTAG Test Mode Select, Input)
The TMS input is the Test Mode Select input. This pin is
internally pulled up.
TDI (JTAG Test Data Input, Input)
The TDI input is the Test Data input. This pin is internally
pulled up.
TDO (JTAG Test Data Output, Output)
The TCLK output is the Test Data Output. This pin is
internally pulled up.
/TRST (JTAG Reset, Input)
The /TRST input is the Reset input, and serves to reset the
Test Access Port circuitry to its reset condition. This pin is
internally pulled up.
VDD, VSS (Positive Power Supply, Ground)
These pins are the main power supply connections to the
MUAC RCP. VDD must be held at +3.3 Volts and ± 0.3
Volts relative to the VSS pin, which is at 0 Volts, system
reference potential, for correct operation of the device.
Note: The TCLK, TMS, TDI, TDO, and /TRST lines are defined
in the IEEE Standard Test Access Port and Boundary-scan
Architecture IEEE Standard. 1149.1-1990 and IEEE Standard.
1149.1a-1993.
相關PDF資料 |
PDF描述 |
|---|---|
| MUAC4K64-50TDC | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP100 |
| MUAC8K64-70TDC | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP100 |
| MUAC4K64-90TDC | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP100 |
| MUAC8K64-70TDI | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP100 |
| MUNICH128X | 4 CHANNEL(S), 8.192M bps, LOCAL AREA NETWORK CONTROLLER, PQFP160 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MUB08A | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1W, Bypass-Capacitor-less Audio Amplifier with Internal Selectable Gain |
| MUB25-10DZ | 制造商:SMC Corporation of America 功能描述:Cylinder, compact, plate, dbl act, 25mm |
| MUB31DH | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:LOW CURRENT HIGH EFFICIENCY LED |
| MUB32DH | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:ULTRA HIGH BRIGHTNESS RED LED LAMP |
| MUB32DH-5 | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:LOW CURRENT HIGH EFFICIENCY RED LED LAMP |
發布緊急采購，3分鐘左右您將得到回復。