- 您現在的位置：買賣IC網 > PDF目錄376207 > MTP805 (Electronic Theatre Controls, Inc.) 8051 Embedded USB/PS2 Keyboard/Mouse Controller PDF資料下載
參數資料
| 型號： | MTP805 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| 中文描述： | 8051嵌入式USB/PS2鍵盤/鼠標控制器 |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 125K |
| 代理商： | MTP805 |
MYSON
TECHNOLOGY
MTP805
(Rev. 0.9)
Revision 0.9 - 7 - 2000/07/19
4. USB and PS2 Mode Detection
After reset, the USB transceiver is disable, and the V33 pin is in high impedance state (no 3.3 volt output).
S/W can detect the application is USB mode or PS2 mode by reading P3.4/P3.5. At first, S/W can set
“PS2KB”=1. This control bit is used to enable the internal 250K pull-up resistor on DP/DM pin. If the chip is
connected to USB Hub, the P3.4/P3.5 is 0 because of the 15K pull-down resistor on Hub. Otherwise,
P3.4/P3.5 is 1.
5. Power-down and Idle Mode
The Power-down/Idle mode is activated by S/W setting the PD/IDL bit in 8051’s PCON register. In Power-
down mode, the MTP805’s X’tal stop oscillating. In Idle mode, the 8051’s instruction clock is stop. The
Power-down/Idle mode is released by any enable interrupt. For standard 8051, Power-down mode is
released only by chip reset.
6. Watch-Dog-Timer(WDT) and Low-Voltage-Reset(LVR)
The WDT is enable by setting the “WDTen” bit in XFR. The time out period is 0.64 second. S/W can clear
WDT by writing the WDT register.
The LVR can generate chip reset when VDD is below 3.0 volt, including both power-on and power-off
process.
7. Fast Clock Option
The CPU can run at double clock rate when S/W setting the “FCLKen” bit in XFR. Once setting, the 8051 is
running at the rate as if a 12MHz X’tal is on OSC pins. However, S/W must clear the FCLKen bit before
entering Power-down mode.
8. USB Engine
The USB engine includes the Serial Interface Engine (SIE), the low-speed USB I/O transceiver and the 3.3
Volt Regulator. The SIE block performs most of the USB interface function with only minimum support from
S/W. Three endpoints are supported. Endpoint 0 is used to receive and transmit control (including SETUP)
packets while Endpoint 1 and endpoint 2 are only used to transmit data packets.
The USB SIE handles the following USB bus activity independently:
1. Bitstuffing/unstuffing
2. CRC generation/checking
3. ACK/NAK
4. TOKEN type identification
5. Address checking
S/W handles the following tasks:
1. Coordinate enumeration by responding to SETUP packets
2. Fill and empty the FIFOs
3. Suspend/Resume coordination
4. Verify and select DATA toggle values
8.1 USB Device Address
The USBADR register stores the device address. This register is reset to all 0 after chip reset or USB bus
reset. S/W must write this register a valid value after the USB enumeration process.
8.2 Endpoint 0 receive
After receiving a packet and placing the data into the Endpoint 0 receive FIFO (RC0FIFO), MTP805 updates
the Endpoint 0 status register (EP0STUS) to record the receive status and then generates an Endpoint 0
相關PDF資料 |
PDF描述 |
|---|---|
| MTP805N | 8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTP805S | 8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTP805V | 8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTU429B | 4-Bit Micro-Controller with LCD Dr |
| MTU8B57EM | EPROM-Based 8-Bit CMOS Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MTP805N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTP805S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTP805V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTP810G | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:MODULAR TELEPHONE PLUGS |
| MTP810U | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:MODULAR TELEPHONE PLUGS |
發布緊急采購，3分鐘左右您將得到回復。