- 您現在的位置：買賣IC網 > PDF目錄359235 > MT9171AP (ZARLINK SEMICONDUCTOR INC) ISO2-CMOS ST-BUS FAMILY PDF資料下載
參數資料
| 型號： | MT9171AP |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | ISO2-CMOS ST-BUS FAMILY |
| 中文描述： | DATACOM, DIGITAL SLIC, PQCC28 |
| 封裝： | PLASTIC, MS-018AB, LCC-28 |
| 文件頁數： | 11/25頁 |
| 文件大?。?/td> | 401K |
| 代理商： | MT9171AP |
Advance Information
MT9171/72
9-125
transparently through the DNIC and is transmitted to
or received from the line at the bit rate selected in the
Control Register.
If the bit rate is 80 kbit/s, only D0 is transmitted and
received. At 160 kbit/s, D0 and D1 are transmitted
and received. When the DINB bit is set in the Control
Register the entire D-channel is transmitted and
received in the B1-channel timeslot.
The C-channel is used for transferring control and
status information between the DNIC and the
system. The Control and Diagnostics Registers are
accessed through the C-channel. They contain
information to control the
DNIC and carry out the
diagnostics as well as the HK bit to be transmitted on
the line as described in Tables 4 and 5. Bits 0 and 1
of the C-channel select between the Control and
Diagnostics Register. If these bits are 0, 0 then the
C-channel information is written to the Control
Register (Table 4). If they are 0, 1 the C-
c
hannel is
written to the Diagnostics Register (Table 5).
The Diagnostics Register Reset bit (bit 2) of the
Control Register determines the reset state of the
Diagnostics Register. If, on writing to the Control
Register, this bit is set to logic “0”, the Diagnostics
Register will be reset coincident with the frame
pulse. When this bit is logic “1”, the Diagnostics
Register will not be reset. In order to use the
diagnostic features, the Diagnostics Register must
be continuously written to. The output C-channel
sends status information from the Status Register to
the system along with the received HK bit as shown
in Table 6.
In MOD mode, the CD port is no longer an ST-BUS
but is a serial bit stream operating at the bit rate
selected. It continues to transfer the C-channel but
the D-channel and the HK bit no longer exist. DUAL
Table 4. Control Register
Notes:
Suggested use of ATTACK:
-At 160 kbit/s full convergence requires 850 ms with ATTACK held high for the first 240 frames or 30 ms.
-At 80 kbit/s full convergence requires 1.75 s with ATTACK held high for the first 480 frames or 60 ms.
When bits 4-7 of the Control Register are all set to one, the DNIC operates in one of the default modes as defined in Table 4a,
depending upon the status of bit-3.
Bit
Name
Description
0
Reg Sel-1
Register Select-1. Must be set to ’0’ to select the Control Register.
1
Reg Sel-2
Register Select-2. Must be set to ’0’ to select the Control Register.
2
DRR
Diagnostics Register Reset. Writing a "0" to this bit will cause a diagnostics register reset
to occur coincident with the next frame pulse as in the MT8972A. When this bit is a logic
"1", the Diagnostics Register will not be reset.
3
BRS
Bit Rate Select. When set to ’0’ selects 80 kbit/s. When set to ’1’, selects 160 kbit/s.
4
DINB
D-Channel in B Timeslot. When ’0’, the D-channel bits (D0 or D0 and D1) corresponding
to the selected bit rate (80 or 160 kbit/s) are transmitted during the normal D-channel bit
times. When set to ’1’, the entire D-channel (D0-D7) is transmitted during the B1-channel
timeslot on the line providing a 64 kbit/s D-channel link.
5
PSEN
Prescrambler/Deprescrambler Enable. When set to ’1’, the data prescrambler and
deprescrambler are enabled. When set to ’0’, the data prescrambler and deprescrambler
are disabled.
6
ATTACK
Convergence Speedup. When set to ’1’, the echo canceller will converge to the reflection
coefficient much faster. Used on power-up for fast convergence.
When ’0’, the echo
canceller will require the normal amount of time to converge to a reflection coefficient.
7
TxHK
Transmit Housekeeping. When set to ’0’, logic zero is transmitted over the line as
Housekeeping Bit. When set to ’1’, logic one is transmitted over the line as Housekeeping
Bit.
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
Reg Sel-1
Reg Sel-2
DRR
BRS
DINB
PSEN
ATTACK
TxHK
Default Mode Selection (Refer to Table 4a)
相關PDF資料 |
PDF描述 |
|---|---|
| MT9171 | ISO2-CMOS ST-BUS⑩ FAMILY Digital Subscriber Interface Circuit Digital Network Interface Circuit |
| MT9171AE | ISO2-CMOS ST-BUS⑩ FAMILY Digital Subscriber Interface Circuit Digital Network Interface Circuit |
| MT9171AN | ISO2-CMOS ST-BUS⑩ FAMILY Digital Subscriber Interface Circuit Digital Network Interface Circuit |
| MT9171AP | ISO2-CMOS ST-BUS⑩ FAMILY Digital Subscriber Interface Circuit Digital Network Interface Circuit |
| MT9173AE1 | Digital Subscriber Interface Circuit with RxSB Digital Network Interface Circuit with RxSB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9171AP1 | 制造商:Microsemi Corporation 功能描述:PB FREE DNIC 1.5UM - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE DNIC 1.5UM - Rail/Tube |
| MT9171APR | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Digital Subscriber Interface Circuit Digital Network Interface Circuit |
| MT9171APR1 | 制造商:Microsemi Corporation 功能描述:PB FREE 1.5UM DNIC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE 1.5UM DNIC - Tape and Reel |
| MT9172 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Digital Subscriber Interface Circuit Digital Network Interface Circuit |
| MT9172AC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO2-CMOS ST-BUS⑩ FAMILY Digital Subscriber Interface Circuit Digital Network Interface Circuit |
發布緊急采購，3分鐘左右您將得到回復。