- 您現在的位置：買賣IC網 > PDF目錄359233 > MT8931CP (Mitel Networks Corporation) CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit PDF資料下載
參數資料
| 型號： | MT8931CP |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
| 中文描述： | 意法半導體的CMOS總線⑩家庭用戶網絡接口電路 |
| 文件頁數： | 21/39頁 |
| 文件大?。?/td> | 833K |
| 代理商： | MT8931CP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Data Sheet
MT8931C
21
Table 11. HDLC Address Recognition Register 1 (Read/Write Add. 00110
B
)
Table 12. HDLC Address Recognition Register 2 (Read/Write Add. 00111
B
)
Table 13. NT Mode C-channel Control Register
(2)
(Write Add. 01000
B
and B0 = 0)
Note 1:
Note 2:
Allow one ST-BUS frame to input the C-channel and one ST-BUS frame to establish the connection.
The C-channel Control Register is updated once every ST-BUS frame. Therefore, this register should not be written to
more than once per frame, otherwise, the last access will override previous ones.
BIT
NAME
DESCRIPTION
B7-B2
R1A7-R1A2 A six bit mask used to interrogate the first byte of the received address (where B7 is MSB).
If address recognition is enabled, any packet failing the address comparison will not be
stored in the Rx FIFO.
B1
NA
Not applicable to address recognition.
B0
A1En
If ’0’, the first byte of the address field will not be used during address recognition.
If ’1’ and the address recognition is enabled, the six most significant bits of the first
address byte will be compared with the first six bits of this register.
BIT
NAME
DESCRIPTION
B7-B1
R2A7-R2A1 A seven bit mask used to interrogate the second byte of the received address (where B7
is MSB). If address recognition is enabled, any packet failing the address comparison will
not be stored in the Rx FIFO. This mask is ignored if the address is a Broadcast (i.e., R2A
= 1111111).
B0
A2En
If ’0’, the second byte of the address field will not be used during address recognition.
If ’1’ and the address recognition is enabled, the seven most significant bits of the second
address byte will be compared with the first seven bits of this register.
BIT
NAME
DESCRIPTION
B7
AR
Setting this bit will initiate the activation of the S-Bus.
If ’0’, the device will remain in the present state.
B6
DR
Setting this bit will initiate the deactivation of the S-Bus.
If ’0’, the device will remain in the present state. This bit has priority over AR.
B5
DinB
If ’1’, the D-channel will be placed in the B1 timeslot allocating 64 kbit/s to the
D-channel.
(1)
If ’0’, the D-channel will assume its position with a 16 kbit/s bandwidth.(1)
B4
Timing
A ’0’ will set the NT in a short passive bus configuration using a fixed timing source (no
compensation for line length).
A ’1’ will set the NT in a point-to-point or extended passive bus configuration with adaptive
timing compensation.
B3
M/S
This bit represents the state of the transmitted M/S-bit. M when HALF=0 and S when
HALF=1.
B2
HALF
The state of this bit identifies which half of the frame will be transmitted on the
S-Bus. The operation of this signal is similar to that of the HALF pin.
B1
TxMFR
A ’1’ in this bit, while HALF = 0, will force the transmission of a multiframe sequence in the
Fa and N bits, i.e., Fa=1 and N=0. A ‘0’ will resume normal operation, i.e., Fa=0 and N=1.
B0
RegSel
If the register select bit is set to ’1’, the control register is redefined as the diagnostic
register. A ’0’ give access to the control register.
相關PDF資料 |
PDF描述 |
|---|---|
| MT8941 | Advanced T1/CEPT Digital Trunk PLL |
| MT8941BE | Advanced T1/CEPT Digital Trunk PLL |
| MT8941BP | Advanced T1/CEPT Digital Trunk PLL |
| MT8941BP1 | Advanced T1/CEPT Digital Trunk PLL |
| MT8941BPR | Round Conductor Flat Cable, 3849/96 30 AWG, .033 (0.85) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8940 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY T1/CEPT Digital Trunk PLL |
| MT8940-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY T1/CEPT Digital Trunk PLL |
| MT8940AC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/CEPT Digital Trunk PLL |
| MT8940AE | 制造商:MITEL 功能描述: |
| MT8941 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Advanced T1/CEPT Digital Trunk PLL |
發布緊急采購，3分鐘左右您將得到回復。