- 您現在的位置：買賣IC網 > PDF目錄359233 > MT8931C (Zarlink Semiconductor Inc.) Subscriber Network Interface Circuit PDF資料下載
參數資料
| 型號： | MT8931C |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | Subscriber Network Interface Circuit |
| 中文描述： | 用戶網絡接口電路 |
| 文件頁數： | 24/39頁 |
| 文件大小： | 833K |
| 代理商： | MT8931C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
MT8931C
Data Sheet
24
Table 18. TE Mode Status Register
(2)
(Read Add. 01001
B
)
Note 1:
Bus activity is set when three zeros are received in a time period equivalent to 48 bits or 250
μ
s. It is reset when 128
consecutive ones are received.
The Status Register is updated internally once every ST-BUS frame. Therefore, more than one read access per frame will
return the same value.
Note 2:
Table 19. Master Status Register (Read Add. 10010
B
)
* These two bits can be used along with status bits IS0 and IS1 to distinguish between states F6/F8 and F4/F5 of the device’s state machine in
TE mode. Please refer to “State Machine” section of Application Note MSAN-141 for further details.
BIT
NAME
DESCRIPTION
B7
Sync/BA
This bit is set if the device has achieved frame synchronization while the activation
request is asserted (DR = 0 and AR = 1). If there is a deactivation request or that AR is
low (DR = 1 or AR = 0), this pin indicates the presence of bus activity
(1)
. A bus activity
identifies the reception of INFO frames (INFO2 or INFO4).
B6-B5
IS0-IS1
Binary encoded state sequence.
IS0 - IS1
0 - 0
- deactivated
0 - 1
- synchronized
1 - 0
- activation request
1 - 1
- activated
B4
M/S
This bit respresents the state of the received M/S-bit. M when HALF=0 and S when
HALF=1
B3
HALF
The state of this bit identifies which half of the S-Bus frame is currently being output on the
ST-BUS.
B2
RxMFR
A ’1’ when HALF=0 indicates that the multiframe pattern on Fa and N has been detected.
B1
Priority
The status of this bit indicates the internal priority of the device within the designated
priority class. If 1, then it has high priority within the priority class designated in B4 of
control register. If 0, then it has low priority within the priority class designated in B4 of
control register.
B0
DCack
A ’1’ indicates that the device has gained access to the D-channel and has transmitted an
opening flag. This bit is reset to ‘0’ when the closing flag of the last packet in the TxFIFO
is transmitted and the internal priority is reduced from high to low. A collision during
transmission will also reset this bit back to ‘0’
.
BIT
NAME
DESCRIPTION
B7-B2
NA
Not available.
B1*
INFO1
In TE mode, this bit is set to ‘1’ only when the device is transmitting INFO1.
Not available in NT mode.
B0*
INFO0
In NT or TE mode, this bit is set to ‘1’ only when the device is transmitting INFO0.
相關PDF資料 |
PDF描述 |
|---|---|
| MT8931CE | Subscriber Network Interface Circuit |
| MT8931CP | Subscriber Network Interface Circuit |
| MT8931C-1 | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
| MT8931CE | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8931C | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8931C-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
| MT8931CC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8931CE | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8931CP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8940 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY T1/CEPT Digital Trunk PLL |
發布緊急采購，3分鐘左右您將得到回復。