- 您現在的位置：買賣IC網 > PDF目錄69040 > MSP430A004IPWR (TEXAS INSTRUMENTS INC) 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | MSP430A004IPWR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 14/47頁 |
| 文件大?。?/td> | 917K |
| 代理商： | MSP430A004IPWR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
MSP430x11x2, MSP430x12x2
MIXED SIGNAL MICROCONTROLLER
SLAS361D JANUARY 2002 REVISED AUGUST 2004
21
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (continued)
wake-up from lower power modes (LPMx)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
t(LPM0)
VCC = 2.2 V/3 V
100
t(LPM2)
VCC = 2.2 V/3 V
100
ns
f(MCLK) = 1 MHz,
VCC = 2.2 V/3 V
6
t(LPM3)
f(MCLK) = 2 MHz,
VCC = 2.2 V/3 V
6
s
(LPM3)
Delay time (see Note 1)
f(MCLK) = 3 MHz,
VCC = 2.2 V/3 V
6
f(MCLK) = 1 MHz,
VCC = 2.2 V/3 V
6
t(LPM4)
f(MCLK) = 2 MHz,
VCC = 2.2 V/3 V
6
s
(LPM4)
f(MCLK) = 3 MHz,
VCC = 2.2 V/3 V
6
NOTES:
1. Parameter applicable only if DCOCLK is used for MCLK.
USART (see Note 1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VCC = 2.2 V
200
430
800
t(τ)
USART: deglitch time
VCC = 3 V
150
280
500
ns
NOTES:
1. The signal applied to the USART receive signal/terminal (URXD) should meet the timing requirements of t(τ) to ensure that the URXS
flip-flop is set. The URXS flip-flop is set with negative pulses meeting the minimum-timing condition of t(τ). The operating conditions
to set the flag must be met independently from this timing constraint. The deglitch circuitry is active only on negative transitions on
the URXD line.
RAM
PARAMETER
MIN
NOM
MAX
UNIT
V(RAMh)
CPU halted (see Note 1)
1.6
V
NOTES:
1. This parameter defines the minimum supply voltage VCC when the data in the program memory RAM remains unchanged. No
program execution should happen during this supply voltage condition.
POR brownout, reset (see Notes 1 and 2)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
td(BOR)
2000
s
VCC(start)
dVCC/dt ≤ 3 V/s
0.7
× V(B_IT)
V
V(B_IT)
dVCC/dt ≤ 3 V/s
1.71
V
Vhys(B_IT)
Brownout
dVCC/dt ≤ 3 V/s
70
130
180
mV
t(reset)
Pulse length needed at RST/NMI pin to accepted reset internally,
VCC = 2.2 V/3 V
2
s
NOTES:
1. The current consumption of the brown-out module is already included in the ICC current consumption data.
2. During power up, the CPU begins code execution following a period of td(BOR) after VCC = V(B_IT) + Vhys(B_IT).
The default DCO settings must not be changed until VCC ≥ VCC(min), where VCC(min) is the minimum supply voltage for the
desired operating frequency. See the MSP430x1xx Family User’s Guide for more information on the brownout circuit.
相關PDF資料 |
PDF描述 |
|---|---|
| MSP430A005IPWR | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO28 |
| MSP430A004IPW | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| MSP430A019IRHBR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430A019IRHBT | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430C111IJL | 16-BIT, MROM, RISC MICROCONTROLLER, CDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSP430A005IPW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430A005IPWR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430A009IPM | 制造商:Texas Instruments 功能描述: |
| MSP430A009IPMR | 功能描述:16位微控制器 - MCU 16B Ultra-Lo-Pwr Microcntrlr,48kB Fl RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MSP430A010IPMR | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。