- 您現在的位置：買賣IC網 > PDF目錄378019 > MSM9006-02 (OKI SEMICONDUCTOR CO., LTD.) Circular Connector; Body Material:Aluminum Alloy; Series:MS3111; Number of Contacts:61; Connector Shell Size:24; Connecting Termination:Solder; Circular Shell Style:Cable Receptacle; Circular Contact Gender:Pin PDF資料下載
參數資料
| 型號： | MSM9006-02 |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; Body Material:Aluminum Alloy; Series:MS3111; Number of Contacts:61; Connector Shell Size:24; Connecting Termination:Solder; Circular Shell Style:Cable Receptacle; Circular Contact Gender:Pin |
| 中文描述： | 液晶顯示驅動器，帶有鍵盤掃描功能 |
| 文件頁數： | 13/18頁 |
| 文件大?。?/td> | 130K |
| 代理商： | MSM9006-02 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁
MSM9006-01, -02
Semiconductor
13/18
Keyscan
Keyscan starts when the key status is changed, or when the "Keyscan Start + key data output"
command is entered. Scan continues until the "Keyscan Stop" command is entered. (Scan is in
stop state at power-on reset.)
When 1 keyscan cycle ends, the INT signal goes to "H" level, so this signal can be used as an
interrupt flag. The INT signal is reset when the LOAD pulse is input after the key data is output,
when the "Keyscan Stop" command is entered, or when a reset signal is applied.
T
SCN
R0
R1
R2
R3
R4
INT
Keyscan Start Command Entered,
or Key Status Changed
Data Read
Keyscan Stop
Command Entered
Data Read
Data Read
Notes: 1. A recognition error (that is, a switch that was not pressed is recognized as being
pressed) may occur when three or more key switches are pressed at the same time.
If simultaneous pressing of three or more key switches must be recognized, insert
diodes serially to each switch. If simultaneous pressing of three or more key switches
is required not to be recognized, a possible approach is to program so that the entire
key information will be ignored if there are three or more 1s in read data.
2. A change of key status is detected as a change of column inputs (
C0
-
C4
). Therefore
if multiple switches which connected to the same column are pressed at the same
time, it will not be detected as a change of key status.
相關PDF資料 |
PDF描述 |
|---|---|
| MSM9202-01 | 5 x 7 Dot Character x 16-Digit Display Controller/Driver with Character RAM |
| MSM9202 | 5×7 Dot Character×16-Digit Display Controller/Driver with Character RAM(具有字符RAM，字型為5×7點陣且12英寸顯示的真空管控制/驅動器) |
| MSM9565 | MSM9565 |
| MSM9802DEMO Board | DEMO(機內掩膜ROM話音合成芯片(DEMO)) |
| MSM9802 | Voice Synthesis IC with Built-in Mask ROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM9006-02GS-BK | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function |
| MSM9006-02GS-BK-7 | 功能描述:LCD 驅動器 LCD Controller 1/4 Duty RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MSM9009 | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:20 VOICE SMART |
| MSM900BEV | 制造商:ADL 制造商全稱:ADL 功能描述:500MHz, 128MB-1024MB DDR333-RAM |
| MSM9011 | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:20 VOICE SMART |
發布緊急采購，3分鐘左右您將得到回復。