參數資料
型號： MSM9005-xx
廠商： OKI SEMICONDUCTOR CO., LTD.
英文描述： DOT MATRIX LCD CONTROLLER WITH 8-DOT COMMON DRIVER AND 65-DOT SEGMENT DRIVER
中文描述： 點陣LCD控制器與8點通用驅動程序和65點段驅動
文件頁數： 19/30頁
文件大?。?/td> 296K
代理商： MSM9005-XX
Semiconductor
MSM9005-xx
19/30
FEDL9005-03
2. Display on/off command (DISP command)
This command is used to select LCD panel display-on mode and display-off mode. Setting
DI = "0" enters display-off mode. At this time, the output voltage of all segments and common
output pins go to V
DD
level and the LCD panel goes out. Setting DI = "1" enters display-on
mode. At this time, the LCD panel restarts the status display before entering display-off
mode.
[DISP command format]
1
0
0
*
1
0
0
DI
D8 D7 D6 D5 D4 D3 D2 D1
DISP
command
Display-off mode is set when DI = “0”
Display-on mode is set when DI = “1”
*: Don't care
3. Arbitrator Blink Control 1/5 command (ABBC 1/5 command)
This command is used to select the type of writing arbitrator blink data to the Arbitrator Blink
RAM (ABB RAM). This command is used along with the Character Blink on/off command
or with the Arbitrator Blink command, explained below.
Setting BC = "0" enables writing arbitrator blink data in 5-bit units using the CHB command.
Setting BC = "1" enables writing arbitrator blink data in 1 bit unit using the ABB command.
[ABBC 1/5 command format]
1
0
0
1
1
1
0
BC
D8 D7 D6 D5 D4 D3 D2 D1
DISP
command
BC = "0" enables writing in 5-bit unit.
BC = "1" enables writing in 1-bit unit.
4. Character Blink on/off command (CHB command)
This command is used to blink a character and arbitrator in 5-dot units. Blinking can be set
for each address pointer value. This command is used with the ABBC 1/5 command,
explained above.
If CB = "0" is set when the address pointer value is 00H to 0CH, "0" is written to Character Blink
RAM (CHB RAM), and the blinking of a character displayed in the segments corresponding
to the address pointer value stops. If CB = "1" is set, "1" is written to CHB RAM, and the
character displayed in the segments corresponding to the address pointer value starts
blinking.
If CB = "0" is set when the address pointer value is 10H to 1CH, "0" is written to the arbitrator
blink RAM (ABB RAM) and the blinking of the arbitrator displayed in the segments
corresponding to the address pointer value stops. If CB = "1" is set, "1" is written to the ABB
RAM, and the arbitrator displayed in the segments corresponding to the address pointer
value starts blinking.
Set the address pointer value by the LPA command before executing this command.
Transfer the LPA command, ABBC 1/5 command and CHB command as follows.
相關PDF資料
PDF描述
MSM9006-01 LCD Driver with Keyscan Function
MSM9006-02 Circular Connector; Body Material:Aluminum Alloy; Series:MS3111; Number of Contacts:61; Connector Shell Size:24; Connecting Termination:Solder; Circular Shell Style:Cable Receptacle; Circular Contact Gender:Pin
MSM9202-01 5 x 7 Dot Character x 16-Digit Display Controller/Driver with Character RAM
MSM9202 5×7 Dot Character×16-Digit Display Controller/Driver with Character RAM(具有字符RAM，字型為5×7點陣且12英寸顯示的真空管控制/驅動器)
MSM9565 MSM9565
相關代理商/技術參數
參數描述
MSM9006-01 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function
MSM9006-01GS-BK 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function
MSM9006-02 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function
MSM9006-02GS-BK 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function
MSM9006-02GS-BK-7 功能描述:LCD 驅動器 LCD Controller 1/4 Duty RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*