- 您現在的位置：買賣IC網 > PDF目錄378018 > MSM7728 (OKI SEMICONDUCTOR CO., LTD.) Single Rail Linear CODEC PDF資料下載
參數資料
| 型號： | MSM7728 |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 元件分類： | Codec |
| 英文描述： | Single Rail Linear CODEC |
| 中文描述： | 單軌線性編解碼器 |
| 文件頁數： | 7/23頁 |
| 文件大?。?/td> | 150K |
| 代理商： | MSM7728 |
Semiconductor
MSM7728
7/23
WRN, RDN, DCLK, CDIN, CDOUT
Serial control ports for microcontroller interface.
Writing data to 8-bit control registers allows controling the transmit speech path/receive speech
path mute, transmit speech path/receive speech path level, PB tone, service tone, and ringer.
WRN is the write control signal input, RDN is the read control signal input, DCLK is the clock
signal input for data shift, CDIN is the control data input, CDOUT is the control data output.
When reset (RSTN=0), the control registers are reset to the initial values as described in "Control
Data Description".
The initial values remains unchanged until control data is written after reset.
Writing of control data: When WRN is at digital "0", data that is entered in CDIN is shifted at the
rising edge of the DCLK signal pulse and is latched in an internal control register.
Reading of control data: When RDN is at digital "0", control data is output from CDOUT at the
rising edge of a DCLK signal pulse.
See Figure 2 for write and read timings.
RINGP, RINGN
Ringer (sounder) drive outputs.
The sounder can be structured by putting a piezo-electric type sounding body (equivalent
capacitance: less than 70nF) between RINGP and RINGN.
LED
Ringer digital level output. This pin is used for LED blinking synchronous with the ringer.
LA
General latch output. This output is used as a control signal for a peripheral circuit because this
output can be set to digital "0" or "1" by writing data from a microcontroller interface.
TOUT
PB tone/service tone output. When SW6 is in the ON state, tone is output.
The output resistance of this pin is approximately 10k
W
, which should be taken into account
when using it externally.
RSTN
Control register reset signal input. When this pin is set to digital "0" level.
All control registers are reset to the initial values.
Be sure to reset the control registers after turning on the power.
相關PDF資料 |
PDF描述 |
|---|---|
| MSM7731-01 | Multifunction PCM CODEC (Voice Signal Processor) |
| MSM7731-02 | Dual Echo Canceler & Noise Canceler with Dual Codec for Hands-Free |
| MSM80C154S | CMOS 8-bit Microcontroller |
| MSM83C154S | Electrical, Duct/Raceway (Trunking); |
| MSM80C31 | CMOS 8-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM7731 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:Dual Echo Canceler & Noise Canceler with Dual Codec for Hands-Free |
| MSM7731-01 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:Multifunction PCM CODEC (Voice Signal Processor) |
| MSM7731-02 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:Dual Echo Canceler & Noise Canceler with Dual Codec for Hands-Free |
| MSM7731-02GAZ020 | 制造商:ROHM Semiconductor 功能描述: |
| MSM7731-02GAZ03A | 制造商:ROHM Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。