- 您現在的位置：買賣IC網 > PDF目錄378678 > MSM6665-xx (OKI SEMICONDUCTOR CO., LTD.) DOT MATRIX LCD CONTROLLER WITH 17-DOT COMMON DRIVER AND 80-DOT SEGMENT DRIVER PDF資料下載
參數資料
| 型號： | MSM6665-xx |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | DOT MATRIX LCD CONTROLLER WITH 17-DOT COMMON DRIVER AND 80-DOT SEGMENT DRIVER |
| 中文描述： | 點陣LCD控制器，17點通用驅動程序和80點段驅動 |
| 文件頁數： | 12/30頁 |
| 文件大?。?/td> | 261K |
| 代理商： | MSM6665-XX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
12/30
Semiconductor
MSM6665-xx
Command Description
[D7, D6, D5, D4, D3, D2, D1, D0], X=don’t care
LPA (Load Pointer Address)
[1,1,A5,A4,A3,A2,A1,A0]
The command sets "address" data into the address pointer to specify an address on
which command execution affects and an address where display data is stored. The
"address" is a number between 0H and 2FH, given by A0 through A5 in hexadecimal.
When addresses 30H through 3FH are specified, display data and CHB, CSC, CSB, CCB
commands become invalid through an address pointer is set up. Normally, the address
pointer is a loop of 0H through 2FH.
LOT (Load Option)
[1,0,1,1,X,X,I1,I0]
This command indicates some specific operation of display at the current address which
is performed each time of AINC command execution.
Operation is specified by bit I1 and I0 of the command.
I0
0
1
0
Operation
1
I1
0
0
1
1
Operation is cancelled. (No operation)
Hereafter, equivalent to writing blank code at each AINC execution.
Hereafter, Cursor-off and blink-cancellation are executed at each AINC execution.
Both of above two operations are indicated.
Note) When blink-cancellation is executed, all RAM data, which controls blinks for each bit of the
arbitrator, go zeros.
BKCG 1/0 (Bank Change 1/0)
[1,0,0,X,0,0,0,1/0]
Command used to do switching between display address groups (switching between
BANKs), which is valid only when 1/9duty display is selected.
When D0 is "0", display address range becomes 0 through 15, and 32 through 47.
When D0 is "1", display address range becomes 16 through 31, and 32 through 47.
Command execution and display data setting are not affected by Bank setting.
The D0 status is not changed by Reset inputting. The D0 status is unknown when the
system is powered on. So D0 must be set to "0" or "1" with the command.
SOE/D (Serial Out Enable/Disable)
[1,0,0,X,0,1,1,1/0]
Command used to control the impedance of SO output pin.
When D0 is "1", display data is output via SO pin. When D0 is "0", SO pin goes to high
impedance.
The D0 status is not changed by Reset inputting. The D0 status is unknown when the
system is powered on. So D0 must be set to "0" or "1" with the command.
相關PDF資料 |
PDF描述 |
|---|---|
| MSM6679A-110 | Voice Synthesiser(SI/SD話音識別,記錄/播放,語音合成器) |
| MSM7524 | DTMF Transceiver(雙音多頻收發器) |
| MSM7547 | Voice Signal Level Control LSI(音頻信號電平控制LSI) |
| MSM80C86A-10 | 16-Bit CMOS Microprocessor(全靜態設計,最高工作頻率10MHz,數據、地址復用,16位微處理器) |
| MSM80C88A-10 | 8-Bit CMOS Microprocessor(內部結構為16位,外圍接口8位,8位微處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM6669 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:80-DOT LCD SEGMENT DRIVER |
| MSM6679A-110 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:SI/SD Voice Recognizer, Recorder/Player, and Speech Synthesizer |
| MSM6679AL-110 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:SI/SD Voice Recognizer, Recorder/Player, and Speech Synthesizer |
| MSM6684B | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:4,194,304-word x 1-bit Serial Register |
| MSM6685 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:8,388,608-Word x 1-Bit Serial Register |
發布緊急采購，3分鐘左右您將得到回復。