- 您現在的位置：買賣IC網 > PDF目錄358227 > MSK5820-5RHD (MS KENNEDY CORP) 5 V FIXED POSITIVE LDO REGULATOR, 0.45 V DROPOUT, CSFM5 PDF資料下載
參數資料
| 型號： | MSK5820-5RHD |
| 廠商： | MS KENNEDY CORP |
| 元件分類： | 固定正電壓單路輸出LDO穩壓器 |
| 英文描述： | 5 V FIXED POSITIVE LDO REGULATOR, 0.45 V DROPOUT, CSFM5 |
| 封裝： | HERMETIC SEALED, SIP-5 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 494K |
| 代理商： | MSK5820-5RHD |
APPLICATION NOTES
PIN FUNCTIONS
VIN-
This pin provides power to all internal circuitry in-
cluding bias, start-up, thermal limit and overcurrent latch.
Input voltage range is 2.9V to 6.5V.
GND -
Internally connected to ground, this pin should be
connected externally by the user to the circuit ground.
SHUTDOWN -
There are two functions to the SHUTDOWN
pin. It may be used to disable the output voltage or to
reset a current latch condition. To activate the shutdown/
reset functions the user must apply a voltage greater than
1.6V to the SHUTDOWN pin. The output voltage will turn
on when the SHUTDOWN pin is pulled below the thresh-
old voltage. If the SHUTDOWN pin is not used, it should
be connected to ground. It should be noted that with the
shutdown pin tied to ground, a current latch condition
can only be reset by cycling power off, then on.
VOUT -
This is the output pin for the device.
INPUT POWER SUPPLY BYPASSING
To maximize transient response and minimize power sup-
ply transients it is recommended that two 47
μ
F tantalum
capacitors are connected between VIN and ground. A
0.1
μ
F ceramic capacitor should also be used for high fre-
quency bypassing. See typical application circuit.
3
FIGURE 1
Overcurrent protection is provided by the MSK 5820RH
series through the use of a timed latch off circuit. The
internal latch timeout is triggered by an overcurrent con-
dition. To allow for start up surge currents, the timeout is
approximately 5.5mS at 25°C. If the overcurrent condi-
tion remains at the end of the timeout cycle, the regulator
will latch off until the latch is reset. Reset the latch by
pulling the shutdown pin high or cycling VIN off then back
on. A thermal limit condition will trigger the latch with no
time out delay.
OVERCURRENT LATCH
CURRENT LIMIT AND SOA
The MSK 5820RH current limit function is directly af-
fected by the input and output voltages. Figure 1 illus-
trates the relationship between VIN and I
CL
for various
output voltages. It is very important for the user to con-
sult the SOA curve when using input voltages which re-
sult in current limit conditions beyond 4.5 Amps. When
using input voltages which result in current limit above
4.5 Amps, the user must maintain output current within
the SOA curve to avoid damage to the device. Note that 5
Amp maximum is due to current carrying capability of the
internal wirebonds.
REPLACING THE OMR9601/IRUH33P253AIM
When the MSK 5820-2.5RH is used as a replacement
for the IR OMR9601 or IRUH33P253B, the user should
recognize that the MSK 5820-2.5RH does not contain in-
ternal tantalum capacitors on the input and output.
The MSK 5820RH sinks increased current during startup
to bring up the output voltage. Reference the "Saturated
Drive Current vs. Input Voltage" graph in the
typicReference the MSK 5826RH RAD REPORT for ELDRS
Results.al performance curves of this data sheet and the
"Understanding Startup Surge Current With MS Kennedy's
RH1573 Based Rad Hard LDO Regulators" application note
in the application notes section of the MS Kennedy Web
site for more information.
http://www.mskennedy.com/
START UP CURRENT
Rev. G 1/11
OUTPUT CAPACITOR SELECTION
Low ESR output capacitors are required to maintain regu-
lation and stability. Four CWR29FB227 (AVX PN
TAZH227K010L) tantalum capacitors in parallel with ce-
ramic decoupling capacitors (0.1
μ
F typical) provides suf-
ficient gain and phase margin for most applications. The
maximum ESR specification for the CWR29FB227 capaci-
tor is 180m
Ω
at 100kHz and is sufficient for many appli-
cations. MSK has found through full WCCA that screen-
ing for a maximum ESR of 57m
Ω
ensures EOL stability
criteria to be met for many applications with the most
stringent requirements. The typical ESR of the
TAZH227K010L from AVX is 49m
Ω
. Analysis of the fi-
nal design is recommended to ensure stability require-
ments are met.
相關PDF資料 |
PDF描述 |
|---|---|
| MSK5822-5KRHU | 5 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, CSFM5 |
| MSK5827HRHUA | ADJUSTABLE POSITIVE LDO REGULATOR, CSFM5 |
| MSM-2170-FX-BMA-02 | 0 MHz - 18000 MHz 50 ohm RF/MICROWAVE TERMINATION |
| MSM-2170-FX-NNN-02 | 0 MHz - 18000 MHz 50 ohm RF/MICROWAVE TERMINATION |
| MSM-2170-FX-SMA-02 | 0 MHz - 18000 MHz 50 ohm RF/MICROWAVE TERMINATION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSK600 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK601 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK601B | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK604 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:NEGATIVE OUTPUT WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK604B | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:NEGATIVE OUTPUT WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。