- 您現在的位置：買賣IC網 > PDF目錄45388 > MSC8254SVT800B (FREESCALE SEMICONDUCTOR INC) 0-BIT, OTHER DSP, PBGA783 PDF資料下載
參數資料
| 型號： | MSC8254SVT800B |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | 0-BIT, OTHER DSP, PBGA783 |
| 封裝： | 29 X 29 MM, LEAD FREE, PLASTIC, FCBGA-783 |
| 文件頁數： | 51/68頁 |
| 文件大?。?/td> | 909K |
| 代理商： | MSC8254SVT800B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Hardware Design Considerations
MSC8254 Quad-Core Digital Signal Processor Data Sheet, Rev. 4
Freescale Semiconductor
55
3.1.2
Power-On Ramp Time
This section describes the AC electrical specification for the power-on ramp rate requirements for all voltage supplies (including
GVDD/SXPVDD/SXCVDD/QVDD/GVDD/NVDD, all VDD supplies, MVREF, and all AVDD supplies). Controlling the
power-on ramp time is required to avoid falsely triggering the ESD circuitry. Table 39 defines the power supply ramp time
specification.
3.1.3
Power Supply Guidelines
Use the following guidelines for power-up sequencing:
Couple M3VDD with the VDD power rail using an extremely low impedance path.
Couple inputs PLL1_AVDD, PLL2_AVDD and PLL3_AVDD with the VDD power rail using an RC filter (see Figure
There is no dependency in power-on/power-off sequence between the GVDD1, GVDD2, NVDD, and QVDD power
rails.
Couple inputs M1VREF and M2VREF with the GVDD1 and GVDD2 power rails, respectively. They should rise at
the same time as or after their respective power rail.
There is no dependency between RapidIO supplies: SXCVDD1, SXCVDD2, SXPVDD1 and SXPVDD2 and other
MSC8254 supplies in the power-on/power-off sequence
Couple inputs SR1_PLL_AVDD and SR2_PLL_AVDD with SXCVDD1 and SXCVDD2 power rails, respectively,
using an RC filter (see Figure 38).
External voltage applied to any input line must not exceed the I/O supply voltage related to this line by more than 0.6 V at any
time, including during power-up. Some designs require pull-up voltages applied to selected input lines during power-up for
configuration purposes. This is an acceptable exception to the rule during start-up. However, each such input can draw up to
80 mA per input pin per MSC8254 device in the system during power-up. An assertion of the inputs to the high voltage level
before power-up should be with slew rate less than 4 V/ns.
The device power rails should rise in the following sequence:
1.
VDD (and all coupled supplies)
2.
After the above rails rise to 90% of their nominal voltage, the following I/O power rails may rise in any sequence (see
Figure 34): QVDD, NVDD, GVDD1, and GVDD2.
Table 39. Power Supply Ramp Rate
Parameter
Min
Max
Unit
Required ramp rate.
—
36000
V/s
Notes:
1.
Ramp time is specified as a linear ramp from 10% to 90% of nominal voltage of the specific voltage supply. If the ramp is
non-linear (for example, exponential), the maximum rate of change from 200 to 500 mV is the most critical because this range
might falsely trigger the ESD circuitry.
2.
Required over the full recommended operating temperature range (see Table 3).
3.
All supplies must be at their stable values within 50 ms.
Figure 34. Supply Ramp-Up Sequence
VDD, MVDD, M3VDD
90%
NVDD, QVDD, GVDD1, GVDD2
相關PDF資料 |
PDF描述 |
|---|---|
| MSC8254TVT1000B | 0-BIT, OTHER DSP, PBGA783 |
| MSC8256SVT800B | 0-BIT, OTHER DSP, PBGA783 |
| MSC8256TVT800B | 0-BIT, OTHER DSP, PBGA783 |
| MSC8256SVT1000B | 0-BIT, OTHER DSP, PBGA783 |
| MSM5547RS | 0 TIMER(S), REAL TIME CLOCK, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSC8254TVT1000B | 功能描述:數字信號處理器和控制器 - DSP, DSC DSPStarcore 4-core RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| MSC8254TVT800B | 功能描述:數字信號處理器和控制器 - DSP, DSC DSPStarcore 4-core RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| MSC8256 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Six-Core Digital Signal Processor |
| MSC8256_11 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Six-Core Digital Signal Processor |
| MSC8256ETAG1000B | 制造商:Freescale Semiconductor 功能描述:DSP,STARCORE, 6-CORE - Bulk |
發布緊急采購，3分鐘左右您將得到回復。