- 您現在的位置：買賣IC網 > PDF目錄45388 > MSC8122TVT6400 (FREESCALE SEMICONDUCTOR INC) 32-BIT, 400 MHz, OTHER DSP, PBGA431 PDF資料下載
參數資料
| 型號： | MSC8122TVT6400 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | 32-BIT, 400 MHz, OTHER DSP, PBGA431 |
| 封裝： | LEAD FREE, FCBGA-431 |
| 文件頁數： | 36/48頁 |
| 文件大?。?/td> | 1158K |
| 代理商： | MSC8122TVT6400 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Hardware Design Considerations
MSC8122 Quad Digital Signal Processor Data Sheet, Rev. 16
Freescale Semiconductor
41
Figure 34. For optimal noise filtering, place the circuit as close as possible to VCCSYN. The 0.01-F capacitor should be closest
to VCCSYN, followed by the 10-F capacitor, the 10-nH inductor, and finally the 10-Ω resistor to VDD. These traces should be
kept short and direct. Provide an extremely low impedance path to the ground plane for GNDSYN. Bypass GNDSYN to VCCSYN
by a 0.01-F capacitor located as close as possible to the chip package. For best results, place this capacitor on the backside of
the PCB aligned with the depopulated void on the MSC8122 located in the square defined by positions, L11, L12, L13, M11,
M12, M13, N11, N12, and N13.
3.3
Connectivity Guidelines
Unused output pins can be disconnected, and unused input pins should be connected to the non-active value, via resistors to
VDDH or GND, except for the following:
If the DSI is unused (DDR[DSIDIS] is set), HCS and HBCS must pulled up and all the rest of the DSI signals can be
disconnected.
When the DSI uses synchronous mode, HTA must be pulled up. In asynchronous mode, HTA should be pulled either
up or down, depending on design requirements.
HDST
can be disconnected if the DSI is in big-endian mode, or if the DSI is in little-endian mode and the
DCR[DSRFA] bit is set.
When the DSI is in 64-bit data bus mode and DCR[BEM] is cleared, pull up HWBS[1–3]/HDBS[1–3]/HWBE[1–3]/
HDBE[1–3]
and HWBS[4–7]/HDBS[4–7]/HWBE[4–7]/HDBE[4–7]/PWE[4–7]/PSDDQM[4–7]/PBS[4–7].
When the DSI is in 32-bit data bus mode and DCR[BEM] is cleared, HWBS[1–3]/HDBS[1–3]/HWBE[1–3]/HDBE[1–3]
must be pulled up.
When the DSI is in asynchronous mode, HBRST and HCLKIN should either be disconnected or pulled up.
When the DSI uses sliding window address mode (DCR[SLDWA] = 1), the external HA[11–13] signals must be
connected (tied) to the correct voltage levels so that the host can perform the first access to the DCR. After reset, the
DSI expects full address mode (DCR[SLDWA] = 0). The DCR address in the DSI memory map is 0x1BE000, which
requires the following connections:
— HA11 must be pulled high (1)
— HA12 must be pulled high (1)
— HA13 must be pulled low (0)
The following signals must be pulled up: HRESET, SRESET, ARTRY, TA, TEA, PSDVAL, and AACK.
In single-master mode (BCR[EBM] = 0) with internal arbitration (PPC_ACR[EARB] = 0):
— BG, DBG, and TS can be left unconnected.
— EXT_BG[2–3], EXT_DBG[2–3], and GBL can be left unconnected if they are multiplexed to the system bus
functionality. For any other functionality, connect the signal lines based on the multiplexed functionality.
— BR must be pulled up.
— EXT_BR[2–3] must be pulled up if multiplexed to the system bus functionality.
If there is an external bus master (BCR[EBM] = 1):
— BR, BG, DBG, and TS must be pulled up.
— EXT_BR[2–3], EXT_BG[2–3], and EXT_DBG[2–3] must be pulled up if multiplexed to the system bus
functionality.
In single-master mode, ABB and DBB can be selected as IRQ inputs and be connected to the non-active value. In other
modes, they must be pulled up.
Figure 34. VCCSYN Bypass
VDD
0.01 F
10 F
VCCSYN
10
Ω
10nH
相關PDF資料 |
PDF描述 |
|---|---|
| MSC8122TVT4800V | 32-BIT, 300 MHz, OTHER DSP, PBGA431 |
| MSC8122MP8000 | 32-BIT, 500 MHz, OTHER DSP, PBGA431 |
| MSC8144ETVT800B | 133 MHz, OTHER DSP, PBGA783 |
| MSC8144EVT1000A | 133 MHz, OTHER DSP, PBGA783 |
| MSC8144ESVT800B | 133 MHz, OTHER DSP, PBGA783 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSC8122TVT6400V | 功能描述:IC DSP QUAD 16B 400MHZ 431FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| MSC8122VT8000 | 功能描述:IC DSP QUAD 16B 500MHZ 431FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| MSC81250M | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:RF & MICROWAVE TRANSISTORS AVIONICS APPLICATIONS |
| MSC8126 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Digital Signal Processor |
| MSC8126_08 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Digital Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。