參數資料
型號: MSA003
廠商: Electronic Theatre Controls, Inc.
英文描述: Mounting Instruction
中文描述: 安裝教學
文件頁數: 1/2頁
文件大小: 524K
代理商: MSA003
Mounting Instruction
MSA 002, 003
For technical data, please look at our catalogue
"Incremental Linear Encoders - Enclosed Models"
Important!
The measuring length of the Linear Encoder
must be longer than the travel length of the machine!
Remove transport brackets prior to operation
Never tilt the encoder head with respect to the extrusion
Do not connect or disconnect the encoder head with the
Digital Readout or Control if the power is on.
The Linear Encoder is not protected against dust and
water drops.
Do not touch the connector pins! (ESD-Instrucion)
Overall cable length should not exceed 30 m!
Mounting notes
The best location for mounting a Linear Encoder
is to mount it as close to the centerline of the slide,
or as close to the guideways of the machine, as possible.
To mount the Linear Encoder, two mounting surfaces are
required; one for the extrusion and one for the encoder
head. If the unit cannot be mounted directly onto the slide,
then mounting brackets would be required.
Mount the Linear Encoder so that the encoder head never
runs into the end of the extrusion, for overtraveling the
measuring length will destroy the unit!
If possible, the extrusion should be mounted on the moving
part of the machine guideway and the encoder head fixed,
so that the cable is rigidly attached to the machine and
continuous cable flexure and the chance of a cable snag
are eliminated.
Inspection of the mounting
Move the slide over the full range of motion to make sure
that full machine movement range can be obtained
without the encoder contacting the end of the scale
extrusion. Otherwise, the Linear Encoder will be
damaged!
Tying down the cables
Lay the cable so that the minimal bending radius is not
exceeded.
When you have mounted the encoder head at the
moving part of your machine, the cable should be
laying in a drag-chain.
Overall cable length should not exceed 30 m!
Mounting of the encoder head
Move the encoder head carefully by hand to the
mounting surface.
Initially, lightly tighten the screws.
Adjust the encoder head gap to the mounting gap and
tolerance (1 mm gap), and tighten the mounting screws
according to the specifications.
Mounting of the extrusion
First, mount the extrusion and loosely tighten
the mounting screws.
Adjust the mounting so that the extrusion is parallel
to the machine guideway, and tighten the mounting
screws according to the specifications.
Number 07/03 Art., Dok.Nr. BGB0019
相關PDF資料
PDF描述
MSA7 REFLECTIVE OBJECT SENSOR
MSC1000-029 Analog Multiplexer Module (16 Channel)
MSC1201 Precision Analog-to-Digital Converter(ADC) and Current-Output Digital-to-Analog Converter(DAC) with 8051 Microcontroller and Flash Memory(帶有8051微控制器和閃存芯片的精密模數轉換器和電流輸出數模轉換器)
MSC1200 Precision Analog-to-Digital Converter(ADC) and Current-Output Digital-to-Analog Converter(DAC) with 8051 Microcontroller and Flash Memory(帶有8051微控制器和閃存芯片的精密模數轉換器和電流輸出數模轉換器)
MSC1202 Precision Analog-to-Digital Converter(ADC) and Current-Output Digital-to-Analog Converter(DAC) with 8051 Microcontroller and Flash Memory(帶有8051微控制器和閃存芯片的精密模數轉換器和電流輸出數模轉換器)
相關代理商/技術參數
參數描述
MSA-0100 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Cascadable Silicon Bipolar MMIC Amplifier
MSA-0100-GP4 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Cascadable Silicon Bipolar MMIC Amplifier
MSA0104 制造商:Agilent Technologies 功能描述: 制造商:AGILNT 功能描述:
MSA-0104 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Cascadable Silicon Bipolar MMIC Amplifier
MSA-0104_97 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Cascadable Silicon Bipolar MMIC Amplifier