- 您現在的位置：買賣IC網 > PDF目錄45276 > MR80C32-20/883:RD (ATMEL CORP) 8-BIT, 20 MHz, MICROCONTROLLER, CQCC44 PDF資料下載
參數資料
| 型號： | MR80C32-20/883:RD |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 20 MHz, MICROCONTROLLER, CQCC44 |
| 封裝： | LCC-44 |
| 文件頁數： | 46/81頁 |
| 文件大小： | 663K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
50
ATtiny28L/V
1062F–AVR–07/06
1.
Set BS to “1”. This selects high data.
2.
Give WR a negative pulse. This starts programming of the data byte. RDY/BSY
goes low.
3.
Wait until RDY/BSY goes high to program the next byte.
(See Figure 39 for signal waveforms.)
The loaded command and address are retained in the device during programming. For
efficient programming, the following should be considered:
The command needs to be loaded only once when writing or reading multiple
memory locations.
Address high byte only needs to be loaded before programming a new 256-word
page in the Flash.
Skip writing the data value $FF, that is, the contents of the entire Flash after a Chip
Erase.
These considerations also apply to Flash and signature bytes reading.
Reading the Flash
The algorithm for reading the Flash memory is as follows (refer to “Programming the
Flash” for details on command and address loading):
A: Load Command “0000 0010”.
B: Load Address High Byte ($00 - $03).
C: Load Address Low Byte ($00 - $FF).
1.
Set OE to “0”, and BS to “0”. The Flash word low byte can now be read at DATA.
2.
Set BS to “1”. The Flash word high byte can now be read from DATA.
3.
Set OE to “1”.
Programming the Fuse Bits
The algorithm for programming the Fuse bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
A: Load Command “0100 0000”.
D: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
Bit 4 = INTCAP Fuse
Bit 3 = CKSEL3 Fuse
Bit 2 = CKSEL2 Fuse
Bit 1 = CKSEL1 Fuse
Bit 0 = CKSEL0 Fuse
Bits 7 - 5 = “1”. These bits are reserved and should be left unprogrammed (“1”).
E: Write Data Low Byte.
Programming the Lock Bits
The algorithm for programming the Lock bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
A: Load Command “0010 0000”.
D: Load Data Low Byte. Bit n = “0” programs the Lock bit.
Bit 2 = Lock Bit2
Bit 1 = Lock Bit1
Bits 7 - 3,0 = “1”. These bits are reserved and should be left unprogrammed (“1”).
E: Write Data Low Byte.
The Lock bits can only be cleared by executing Chip Erase.
相關PDF資料 |
PDF描述 |
|---|---|
| MC80C52XXX-16SBD | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| MR83C154XXX-12P883D | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44 |
| MC80C52TXXX-25P883D | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40 |
| IF280C51T-20R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44 |
| IS80C52EXXX-30D | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MR80C32-25 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MR80C32-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MR80C32-36 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MR80C51BH | 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space |
| MR80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。