參數資料
型號: MQ80C52TXXX-36
廠商: TEMIC SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
文件頁數: 210/586頁
文件大?。?/td> 25028K
代理商: MQ80C52TXXX-36
288
8272E–AVR–04/2013
ATmega164A/PA/324A/PA/644A/PA/1284/P
26.8.8
EEPROM Write Prevents Writing to SPMCSR
Note that an EEPROM write operation will block all software programming to Flash. Reading the
Fuses and Lock bits from software will also be prevented during the EEPROM write operation. It
is recommended that the user checks the status bit (EEPE) in the EECR Register and verifies
that the bit is cleared before writing to the SPMCSR Register.
26.8.9
Reading the Fuse and Lock Bits from Software
It is possible to read both the Fuse and Lock bits from software. To read the Lock bits, load the
Z-pointer with 0x0001 and set the BLBSET and SPMEN bits in SPMCSR. When an (E)LPM
instruction is executed within three CPU cycles after the BLBSET and SPMEN bits are set in
SPMCSR, the value of the Lock bits will be loaded in the destination register. The BLBSET and
SPMEN bits will auto-clear upon completion of reading the Lock bits or if no (E)LPM instruction
is executed within three CPU cycles or no SPM instruction is executed within four CPU cycles.
When BLBSET and SPMEN are cleared, (E)LPM will work as described in the Instruction set
Manual.
The algorithm for reading the Fuse Low byte is similar to the one described above for reading
the Lock bits. To read the Fuse Low byte, load the Z-pointer with 0x0000 and set the BLBSET
and SPMEN bits in SPMCSR. When an (E)LPM instruction is executed within three cycles after
the BLBSET and SPMEN bits are set in the SPMCSR, the value of the Fuse Low byte (FLB) will
be loaded in the destination register as shown below. Refer to Table 27-5 on page 300 for a
detailed description and mapping of the Fuse Low byte.
Similarly, when reading the Fuse High byte, load 0x0003 in the Z-pointer. When an (E)LPM
instruction is executed within three cycles after the BLBSET and SPMEN bits are set in the
SPMCSR, the value of the Fuse High byte (FHB) will be loaded in the destination register as
shown below. Refer to Table 27-4 on page 300 for detailed description and mapping of the Fuse
High byte.
When reading the Extended Fuse byte, load 0x0002 in the Z-pointer. When an (E)LPM instruc-
tion is executed within three cycles after the BLBSET and SPMEN bits are set in the SPMCSR,
the value of the Extended Fuse byte (EFB) will be loaded in the destination register as shown
below. Refer to Table 27-3 on page 299 for detailed description and mapping of the Extended
Fuse byte.
Fuse and Lock bits that are programmed, will be read as zero. Fuse and Lock bits that are
unprogrammed, will be read as one.
26.8.10
Reading the Signature Row from Software
To read the Signature Row from software, load the Z-pointer with the signature byte address
given in Table 26-5 on page 289 and set the SIGRD and SPMEN bits in SPMCSR. When an
LPM instruction is executed within three CPU cycles after the SIGRD and SPMEN bits are set in
Bit
765
432
10
Rd
BLB12
BLB11
BLB02
BLB01
LB2
LB1
Bit
7
65
4
3210
Rd
FLB7
FLB6
FLB5
FLB4
FLB3
FLB2
FLB1
FLB0
Bit
765
4
3210
Rd
FHB7
FHB6
FHB5
FHB4
FHB3
FHB2
FHB1
FHB0
Bit
7
65
4
3210
Rd
EFB2
EFB1
EFB0
相關PDF資料
PDF描述
MD80C32E-12SHXXX 8-BIT, 12 MHz, MICROCONTROLLER, CDIP40
MD80C32E-16SHXXX 8-BIT, 16 MHz, MICROCONTROLLER, CDIP40
MC80C52XXX-30SHXXX 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CDIP40
MD80C52TXXX-20/883 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40
MD80C52XXX-20/883 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
MQ82370-20 制造商:Rochester Electronics LLC 功能描述:- Bulk
MQ8238020 制造商:Intel 功能描述:CONTROLLER: OTHER
MQ82380-20 制造商:Rochester Electronics LLC 功能描述:- Bulk
MQ82380-20/R 制造商:Rochester Electronics LLC 功能描述:
MQ82592 制造商:Rochester Electronics LLC 功能描述:- Bulk