參數資料
型號: MPXV5010G6U
廠商: Motorola, Inc.
元件分類: 壓力傳感器
英文描述: Sensor
中文描述: 傳感器
文件頁數: 633/670頁
文件大?。?/td> 6375K
代理商: MPXV5010G6U
4–41
Motorola Sensor Device Data
For More Information On This Product,
Go to: www.freescale.com
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
TEST
LOW–SUPPLY
TRIP
VSS
R1
OSC
LED
FEEDBACK
SILVER
VDD
IRED
I/O
BRASS
STROBE
DETECT
C1
C2
HORN
X1
TO OTHER
MC145011(s),
ESCAPE LIGHT(S),
AUXILIARY ALARM(S),
REMOTE ALARM(S),
AND/OR AUTO–DIALER
IR
CURRENT
R13*
4.7 TO 22
Q1
2.2 M
R5
#
D3
VISIBLE
LED
R7
47 k
R6
100 k
SW1
+
+
MC145011
PUSHBUTTON
TEST
R2
10 M
0.01
μ
F
C6
#
C3
1500 pF
R1
100 k
R3
470
R4
#
100 k
1 TO 22
μ
F
C4**
C1
0.047
μ
F
C2*
4700 pF
R14
560
R11 250 k
D1
IR DETECTOR
R8
8.2 k
R9
5 k
R10
4.7 k
D2
IR EMITTER
R12
1 k
C5
100
μ
F
#
Values for R4, R5, and C6 may differ depending on type of piezoelectric horn used.
* C2 and R13 are used for coarse sensitivity adjustment. Typical values are shown.
R9 is for fine sensitivity adjustment (optional). If fixed resistors are used, R8 = 12 k, R10 is 5.6 k to 10 k, and R9 is eliminated. When R9
is used, noise pickup is increased due to antenna effects. Shielding may be required.
** C4 should be 22
μ
F if supply line resistance is high (up to 50
). C4 could be reduced to 1
μ
F when supply line resistance is < 30
.
V+
Figure 5. Typical Application
PIN DESCRIPTIONS
C1 (Pin 1)
A capacitor connected to this pin as shown in Figure 5
determines the gain of the on–chip photo amplifier during
pushbutton test and chamber sensitivity test (high gain). The
capacitor value is chosen such that the alarm is tripped from
background reflections in the chamber during pushbutton
test.
Av
1 + (C1/10) where C1 is in pF. CAUTION: The value
of the closed–loop gain should not exceed 10,000.
C2 (Pin 2)
A capacitor connected to this pin as shown in Figure 5
determines the gain of the on–chip photo amplifier except
during pushbutton or chamber sensitivity tests.
Av
1 + (C2/10) where C2 is in pF. This gain increases
about 10% during the IRED pulse, after two consecutive
local smoke detections.
Resistor R14 must be installed in series with C2. R14
[1/(12
C2)] – 680 where R14 is in ohms and C2 is in farads.
DETECT (Pin 3)
This input to the high–gain pulse amplifier is tied to the
cathode of an external photodiode. The photodiode should
have low capacitance and low dark leakage current. The
diode must be shunted by a load resistor and is operated at
zero bias.
The Detect input must be ac/dc decoupled from all other
signals, VDD, and VSS. Lead length and/or foil traces to this
pin must be minimized, also. See Figure 6.
STROBE (Pin 4)
This output provides a strobed, regulated voltage refer-
enced to VDD. The temperature coefficient of this voltage is
±
0.2%/
°
C maximum from – 10
°
to 60
°
C. The supply–voltage
coefficient (line regulation) is
±
0.2%/V maximum from 6 to
12 V. Strobe is tied to external resistor string R8, R9, and
R10.
F
Freescale Semiconductor, Inc.
n
.
相關PDF資料
PDF描述
MPXV5010G7U Sensor
MPXV5010GC6T1 Sensor
MPXV5010GC6U Sensor
MPXV5010GC7U Sensor
MPXV5010GP Sensor
相關代理商/技術參數
參數描述
MPXV5010G7U 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Sensor
MPXV5010GC6T1 功能描述:板上安裝壓力/力傳感器 PRES SEN INTEG 10KPA RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides
MPXV5010GC6U 功能描述:板上安裝壓力/力傳感器 PRESS SEN INTEG 10KPA RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides
MPXV5010GC6U 制造商:Freescale Semiconductor 功能描述:IC PRESSURE SENSOR 0 TO 10KPA SOP-8
MPXV5010GC7U 功能描述:板上安裝壓力/力傳感器 PRESS SEN INTEG 10KPA RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides