- 您現在的位置：買賣IC網 > PDF目錄359200 > MPXM2010 (飛思卡爾半導體(中國)有限公司) 10kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors(10kPa片內溫度補償和校準硅壓力傳感器) PDF資料下載
參數資料
| 型號： | MPXM2010 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 10kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors(10kPa片內溫度補償和校準硅壓力傳感器) |
| 中文描述： | 10kPa片上溫度補償 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 128K |
| 代理商： | MPXM2010 |
MPXM2010 SERIES
3
Sensor Device Data
Freescale Semiconductor
LINEARITY
Linearity refers to how well a transducer’s output follows
the equation: V
out
= V
off
+ sensitivity x P over the operating
pressure range. There are two basic methods for calculating
nonlinearity: (1) end point straight line fit (see Figure 2) or (2)
a least squares best line fit. While a least squares fit gives
the “best case” linearity error (lower numerical value), the
calculations required are burdensome.
Conversely, an end point fit will give the “worst case” error
(often more desirable in error budget calculations) and the cal-
culations are more straightforward for the user. Freescale
Semiconductor’s specified pressure sensor linearities are
based on the end point straight line method measured at the
midrange pressure.
Figure 2. Linearity Specification Comparison
LEAST
SQUARE
DEVIATION
R
PRESSURE(%FULLSCALE)
0
50
100
END POINT
STRAIGHT LINE FIT
EXAGGERATED
PERFORMANCE
CURVE
LEASTSQUARESFIT
STRAIGHTLINE
DEVIATION
OFFSET
ON--CHIP TEMPERATURE COMPENSATION and CALIBRATION
Figure 3 shows the minimum, maximum and typical output
characteristics of the MPXM2010 series at 25
°
C. The output
is directly proportional to the differential pressure and is es-
sentially a straight line.
A silicone gel isolates the die surface and wire bonds from
the environment, while allowing the pressure signal to be
transmitted to the silicon diaphragm.
Figure 3. Output versus Pressure Differential
MIN
TYP
OFFSET
(TYP)
30
20
15
10
5
O 25
0
--5kPa
PSI
2.5
0.362
5
0.725
7.5
1.09
10
1.45
a
MAX
SPAN
RANGE
(TYP)
V
S
= 10 Vdc
T
= 25
°
C
P1 > P2
ORDERING INFORMATION
Device Type
Options
Case No.
MPXM2010D
Non--ported
1320
MPXM2010DT1
Non--ported, Tape and Reel
1320
MPXM2010GS
Ported
1320A
MPXM2010GST1
Ported, Tape and Reel
1320A
相關PDF資料 |
PDF描述 |
|---|---|
| MPXM2051G | 50 kPa On-Chip Temperature Compensated and Calibrated Silicon Pressure Sensors |
| MPXM2053D | 50kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors(50kPa片內溫度補償和校準硅壓力傳感器) |
| MPXM2053GST1 | 50 kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors |
| MPXM2053D | Sensor |
| MPXM2053DT1 | Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPXM2010D | 功能描述:板上安裝壓力/力傳感器 M-PAK RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXM2010DT1 | 功能描述:板上安裝壓力/力傳感器 M-PAK RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXM2010GS | 功能描述:板上安裝壓力/力傳感器 M-PAK PORTED RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXM2010GS | 制造商:Freescale Semiconductor 功能描述:Pressure Sensors IC |
| MPXM2010GST1 | 功能描述:板上安裝壓力/力傳感器 M-PAK PORTED RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
發布緊急采購，3分鐘左右您將得到回復。