參數資料
型號: MPX2053GP
廠商: MOTOROLA INC
元件分類: 壓力傳感器
英文描述: 50 KPA ON CHIP TEMPERATURE COMPENSATED CALIBRATED SILICON PRESSURE SENSORS
中文描述: GAGE, PEIZORESISTIVE PRESSURE SENSOR, 0-7.25Psi, 0.4%, 0-40mV, THROUGH HOLE MOUNT
封裝: UNIBODY PACKAGE-4
文件頁數: 3/12頁
文件大?。?/td> 191K
代理商: MPX2053GP
3
Motorola Sensor Device Data
LINEARITY
Linearity refers to how well a transducer’s output follows
the equation: V
out
= V
off
+ sensitivity x P over the operating
pressure range. There are two basic methods for calculating
nonlinearity: (1) end point straight line fit (see Figure 2) or (2)
a least squares best line fit. While a least squares fit gives
the “best case” linearity error (lower numerical value), the
calculations required are burdensome.
Conversely, an end point fit will give the “worst case” error
(often more desirable in error budget calculations) and the cal-
culations are more straightforward for the user. Motorola’s
specified pressure sensor linearities are based on the end
point straight line method measured at the midrange pressure.
Figure 2. Linearity Specification Comparison
!()
(&*'
+ ) $#
'
%'((*' *!!(!
# %$ #)
()' ) ! # )
-')
%'$'"#
*'+
!() (&*'( )
()' ) ! #
+ ) $#
$()
ON–CHIP TEMPERATURE COMPENSATION and CALIBRATION
Figure 3 shows the minimum, maximum and typical output
characteristics of the MPX2053/MPXV2053G series at 25
°
C.
The output is directly proportional to the differential pressure
and is essentially a straight line.
The effects of temperature on Full–Scale Span and Offset
are very small and are shown under Operating Characteris-
tics.
Figure 3. Output versus Pressure Differential
Figure 4. Cross–Sectional Diagram (not to scale)
$
3%/
%(
9
(%#
'#
).%
$()
).%
ééééééééééé
ééééééééééé
ééééééééééé
ééééééééééé
ééééééééééé
( ! $#
$)
, ' $#
! '"
() #!(( ()!
")! $+'
%$-.
(
')+
$#
%
"-
).%
" #
+
(
+21
)
"%-
% %
°
Figure 4 illustrates the differential or gauge configuration
in the basic chip carrier (Case 344). A silicone gel isolates
the die surface and wire bonds from the environment, while
allowing the pressure signal to be transmitted to the silicon
diaphragm.
The MPX2053/MPXV2053G series pressure sensor oper-
ating characteristics and internal reliability and qualification
tests are based on use of dry air as the pressure media. Me-
dia other than dry air may have adverse effects on sensor
performance and long term reliability. Contact the factory for
information regarding media compatibility in your application.
相關PDF資料
PDF描述
MPX2053D 50 KPA ON CHIP TEMPERATURE COMPENSATED CALIBRATED SILICON PRESSURE SENSORS
MPX2053DP 50 KPA ON CHIP TEMPERATURE COMPENSATED CALIBRATED SILICON PRESSURE SENSORS
MPX2053GVP 50 KPA ON CHIP TEMPERATURE COMPENSATED CALIBRATED SILICON PRESSURE SENSORS
MPX2200 0 to 200 kPa (0 to 29 psi) 40 mV FULL SCALE SPAN (TYPICAL)
MPX2201 0 to 200 kPa (0 to 29 psi) 40 mV FULL SCALE SPAN (TYPICAL)
相關代理商/技術參數
參數描述
MPX2053GP 制造商:Freescale Semiconductor 功能描述:IC PRESSURE SENSOR UNCOMPENSATED 制造商:Freescale Semiconductor 功能描述:IC, PRESSURE SENSOR, UNCOMPENSATED
MPX2053GSX 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Sensor
MPX2053GVP 功能描述:板上安裝壓力/力傳感器 COMPENSATED RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides
MPX206K305R 功能描述:CAP FILM 20UF 10% 305VAC RAD 制造商:illinois capacitor 系列:MPX 包裝:散裝 零件狀態:在售 電容:20μF 容差:±10% 額定電壓 - AC:305V 額定電壓 - DC:- 介電材料:聚丙烯(PP),金屬化 工作溫度:-40°C ~ 110°C 安裝類型:通孔 封裝/外殼:徑向 大小/尺寸:2.264" 長 x 1.181" 寬(57.50mm x 30.00mm) 高度 - 安裝(最大值):1.791"(45.50mm) 端接:PC 引腳 引線間距:2.067"(52.50mm) 應用:EMI,RFI 抑制 等級:X2 特性:- 標準包裝:25
MPX20W1100FA00MB00 功能描述:薄膜電容器 MP 3-X2 1000 pF 250 VAC 4x8.5x13.5 F PCM10 RoHS:否 制造商:Cornell Dubilier 產品類型: 電介質:Polyester 電容:0.047 uF 容差:10 % 電壓額定值:100 V 系列:225P 工作溫度范圍:- 55 C to + 85 C 端接類型:Radial 引線間隔:9.5 mm