<tfoot id="qfuvl"></tfoot>
<form id="qfuvl"></form>
<span id="qfuvl"><pre id="qfuvl"></pre></span>
<li id="qfuvl"></li>
  • <menuitem id="qfuvl"><input id="qfuvl"><strong id="qfuvl"></strong></input></menuitem>
    參數資料
    型號: MPR083EJR2
    廠商: Freescale Semiconductor
    文件頁數: 2/35頁
    文件大小: 0K
    描述: IC CTLR TOUCH SENSR PROX 16TSSOP
    產品培訓模塊: Sensor Toolbox
    標準包裝: 1
    類型: 電容性
    輸入數/鍵: 8 個滑塊
    評估套件: 可供
    數據接口: I²C,串行
    電源電壓: 1.8 V ~ 3.6 V
    電流 - 電源: 1.62mA
    工作溫度: -40°C ~ 85°C
    安裝類型: 表面貼裝
    封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
    供應商設備封裝: 16-TSSOP
    包裝: 剪切帶 (CT)
    配用: DEMOMPR083-ND - BOARD DEMO FOR MPR083 CTLR
    KITMPR083EVM-ND - KIT EVAL 8POSITION ROTARY TOUCH
    其它名稱: MPR083EJR2CT
    MPR083
    Sensors
    10
    Freescale Semiconductor
    3
    Touch Detection
    3.1
    Introduction
    When using a capacitive touch sensor system the raw data must be filtered and interpreted. This process can be done many
    different ways but the method used in the MPR083 is explained in this chapter.
    3.2
    Understanding the Basics
    The rotary interface has to distinguish touch status through varying user conditions (different finger sizes in bare hands or gloves)
    and environmental conditions (electrical and RF noise, sensor contamination with dirt or moisture).
    The rotary circuitry reports touch status as one of the following two conditions:
    1.
    Rotary untouched
    2.
    Rotary touched in one of eight positions.
    The rotary is only touched in one position, ideally near the middle of one of the eight pads. If a touch occurs between pads,
    untouched will be reported.
    3.3
    Conditional Output Scenarios
    Since it is unlikely that in a real world case a single independent touch will occur two specific multi-touch response cases are
    outlined. Methods for changing the sensitivity of the device will be discussed in another Chapter, but the important part is that the
    sensitivity is determined by the strength of an input signal. If more than one input signal is above the selected sensitivity then the
    touch sensor controller interprets this in a specific way. This functionality is broken down into two different cases.
    3.3.1
    Simultaneous Touches
    Any time two touches are detected at the same time the touch sensor controller recognizes this case and accounts for it. Any
    time more than one key is pressed the touches are ignored. Thus the touch sensor controller will show the rotary as untouched.
    In most cases one of the two electrodes will receive a stronger signal than the other. If the difference in capacitance is statistically
    significant between the pad with the stronger signal will be reported.
    This functionality is sometimes called 1-Key Lockout.
    3.3.2
    Sequential Touches
    Another case is when one rotary pad is touched and held and a second rotary pad is then touched and held. For this situation
    the second touch will be ignored and the first touch will continue to be reported.
    If the second touch is released before the first touch then the second touch will be completely ignored. But, if the first touch is
    released before the second then the system will report that the first key is released and that the second key is now touched. This
    functionality is sometimes called 2-Key Rollover.
    3.4
    Rotary Configuration Register
    The Rotary Configuration Register configures a variety of the MPR083 features. Each of these features is described in following
    sections. The I2C slave address of the Rotary Configuration Register is 0x03.
    Figure 14. Rotary Configuration Register
    7
    6
    543210
    R
    RSE
    00
    ACE
    RRBE
    RTBE
    0
    RE
    W
    Reset:
    1
    0
    000001
    = Unimplemented
    相關PDF資料
    PDF描述
    MS27467T23F21SC CONN PLUG 21POS STRAIGHT W/SCKT
    MS27466T21F41PA CONN RCPT 41POS WALL MT W/PINS
    MS3101A28-15P CONN RCPT 35POS FREE HNG W/PINS
    VI-2TK-IW-B1 CONVERTER MOD DC/DC 40V 100W
    D38999/26WG16SB CONN PLUG 16POS STRAIGHT W/SCKT
    相關代理商/技術參數
    參數描述
    MPR083Q 功能描述:電容觸摸傳感器 10 PADS 8 POSITION RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
    MPR083QR2 功能描述:電容觸摸傳感器 10 PADS 8 POSITION RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
    MPR084 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller
    MPR084EJ 功能描述:電容觸摸傳感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
    MPR084EJR2 功能描述:電容觸摸傳感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: