參數資料
型號： MPR083EJ
廠商： Freescale Semiconductor
文件頁數： 11/35頁
文件大?。?/td> 0K
描述： IC CTLR TOUCH SENSR PROX 16TSSOP
產品培訓模塊： Sensor Toolbox
產品目錄繪圖： MPR08(3,4)EJ Top
MPR08(3,4)EJ Side
標準包裝： 96
類型： 電容性
輸入數/鍵： 8 個滑塊
評估套件： 可供
數據接口： I²C，串行
電源電壓： 1.8 V ~ 3.6 V
電流 - 電源： 1.62mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 管件
產品目錄頁面： 2808 (CN2011-ZH PDF)
配用： DEMOMPR083-ND - BOARD DEMO FOR MPR083 CTLR
KITMPR083EVM-ND - KIT EVAL 8POSITION ROTARY TOUCH
MPR083
Sensors
Freescale Semiconductor
19
7
Interrupts
7.1
Introduction
The MPR083 has one interrupt output that is configured by registers and alerts the application when a touch or fault is detected.
When running in Run2 or Stop2 mode where I2C communication is not available this feature alerts the user to sensor touches.
7.2
Condition for Interrupt
There are two cases that latch the Interrupt buffered data available or fault detected.
7.2.1
Buffered Data Available
The interrupt for Buffered Data Available will only trigger when the NDF (No Data Flag) transitions from high to low. This signifies
that there is new data available in the buffer. The interrupt is deasserted on the first read/write of the FIFO Register and cannot
be reasserted for buffered data until the FIFO is empty (either by reading all the data, or clearing the buffer).
7.2.2
Fault Detected
The interrupt for a fault detected condition is triggered any time the Fault condition in the Fault Register transitions from zero to
non-zero. The interrupt is deasserted when the Fault Register is cleared (by writing to the Fault Register).
7.3
Settings
Interrupts are configured through I2C using the Configuration Register (Section 4.7). Two of the settings in this register will affect
the interrupt functionality.
The Interrupt Enable (IRQEN) must be set high for the IRQ to be enabled. When low, all interrupts will be ignored, and the IRQ
pin will never latch.
The Interrupt Rate (IRQR) sets the minimum delay between sequential triggered interrupts. The minimum interrupt period can be
calculated by taking the product of the (MTP + 5) and IRQR with a factor of 4. Thus, for the minimum setting an interrupt would
be triggered no more often than 4 times the master clock.
Equation 4
If the MPR083 is using Run2, the minimum interrupt period would be represented by the following equation.
Equation 5
7.4
IRQ Pin
The IRQ pin is an open-drain, latching interrupt output which requires an external pull-up resistor. The pin will latch down based
on the conditions in Section 6.2. The pin will reset when an I2C transmission reads/writes the appropriate register displaying
information about the source of the interrupt. Thus if the source is buffered data available then a FIFO Buffer read/write will clear
the IRQ pin. If the source is a fault detected then a write of the Fault Register will clear the pin.
MinInterruptPeriod ms
MTP
5
+
IRQR
4
=
MinInterruptPeriod ms
MTP
5
+
8
----------------------
1
+
8
I
RQR 4
=
相關PDF資料
PDF描述
VE-24D-IW-B1 CONVERTER MOD DC/DC 85V 100W
VI-2TX-MX-F3 CONVERTER MOD DC/DC 5.2V 75W
VE-244-IW-B1 CONVERTER MOD DC/DC 48V 100W
VE-21Z-IU-B1 CONVERTER MOD DC/DC 2V 80W
MS27505E23F53SC CONN RCPT 53POS BOX MNT W/SCKT
相關代理商/技術參數
參數描述
MPR083EJR2 功能描述:電容觸摸傳感器 8 POSIT ROTARY RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
MPR083Q 功能描述:電容觸摸傳感器 10 PADS 8 POSITION RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
MPR083QR2 功能描述:電容觸摸傳感器 10 PADS 8 POSITION RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
MPR084 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller
MPR084EJ 功能描述:電容觸摸傳感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*