- 您現在的位置：買賣IC網 > PDF目錄299508 > MPD7D053S (MURATA MANUFACTURING CO LTD) CONV DC/DC 50W 1.5VOUT 17A SMT PDF資料下載
參數資料
| 型號： | MPD7D053S |
| 廠商： | MURATA MANUFACTURING CO LTD |
| 元件分類： | 電源模塊 |
| 英文描述： | CONV DC/DC 50W 1.5VOUT 17A SMT |
| 中文描述： | 1-OUTPUT 25.5 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | MODULE-28/23 |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 293K |
| 代理商： | MPD7D053S |
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.10.4
MPD7D05*S Application
5
5 .4 Remote On/Off Control
The connection to a RC pin controls an Isolated DC-DC Converter to turn on/off.
While the Isolated DC-DC Converter is halted via the remote control feature, the alarm function will not
operate; refer to Alarm Output (section 5-5).
Start
: RC open or connected to -Vin
Halt
: RC connected to +Vin
5 .5 Alarm Output (ALM)
The Alarm Output can be down to the level of -Vin (Open Drain Output), when Over Voltage Protection or Low
Voltage Protection features are activated. The sink current in ALM pin is 10mA max. Multiple Isolated DC-DC
Converters running independently and / or in parallel operation can be simultaneously halted by connecting all
ALM pins, when the Over Voltage Protection or Low Voltage Protection functions are activated by any single
DC-DC Converter. The maximum number connected running DC-DC Converters is 10pcs.
To connect more than 10,please consult Murata.
5 .6 Synchronous Turn-on/off
Multiple Isolated DC-DC Converters running independently and / or in parallel operation can be synchronously
toggled on & off timing among the running converters, of which the input voltage detection circuits are tied to
the detection voltage of a single reference Isolated DC-DC Converter. Every PO pin must be connected for
multiple and/or parallel operation.
The Maximum number connected running DC-DC Converters is
: 10pcs for Multiple operation,
: 5pcs for parallel operation of identical output voltage of this TF50A.
It is NOT possible in using other DC-DC Converters with this TF50A for parallel.
To connect more than the above-stated-number, please consult Murata.
6 Parallel Operation
6 .1 Parallel Operation Description (Current sharing)
When the output current required is more than that available from one DC-DC Converter an alternative rather
than choosing a higher power rated DC-DC Converter is to operate multiple DC-DC Converters in parallel.
It is possible to run up to 5 devices of the same this model in parallel operation.
This series are NOT applicable for parallel operation with other series.
PO pins should be connected so that the turn-on / off of all connected DC-DC Converters are synchronized.
Additionally connecting the ALM pins of the devices in parallel operation enables simultaneous shut down of
all DC-DC Converters when one is halted and generates an ALM signal due to an OVP or LVP condition.
6 .2 Load Balance in Parallel Operation
Neither external load balancing circuit nor reverse-current prevention circuit is necessary for Murata’s DC-DC
converters operating in parallel. Murata’s DC-DC converters are designed to regulate load balancing and
prevent reverse-current.
The combined devices operated in parallel provide an output voltage within the tolerance specified for either
device (e.g. +5% / -3%). This tolerance is maintained throughout the output current variance from zero to
the rated current value. This feature automatically balances the output currents from all of the parallel DC-DC
converters.
相關PDF資料 |
PDF描述 |
|---|---|
| MPD7D056S | CONV DC/DC 50W 2.5VOUT 15A SMT |
| MPD7D057S | CONV DC/DC 50W 3.3VOUT 15A SMT |
| MPD7D058S | CONV DC/DC 50W 5.0VOUT 10A SMT |
| MPDRX103S | CONV DC/DC 28W .8-1.8VOUT SIP |
| MPDRX104S | CONV DC/DC 39W 1.5-3.3VOUT SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPD7D054S | 功能描述:DC/DC轉換器 1.8V +5/-3% 16A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| MPD7D056S | 功能描述:DC/DC轉換器 2.5V +5/-3% 15A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| MPD7D057S | 功能描述:DC/DC轉換器 3.3V +5/-3% 15A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| MPD7D058S | 功能描述:DC/DC轉換器 5V +5/-3% 10A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| MPD7D067S | 功能描述:DC/DC轉換器 3.3V 10.6A 50W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。