- 您現在的位置：買賣IC網 > PDF目錄45374 > MPC92429FAR2 (FREESCALE SEMICONDUCTOR INC) 400 MHz, OTHER CLOCK GENERATOR, PQFP32 PDF資料下載
參數資料
| 型號： | MPC92429FAR2 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 400 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| 封裝： | LQFP-32 |
| 文件頁數： | 1/12頁 |
| 文件大?。?/td> | 292K |
| 代理商： | MPC92429FAR2 |
MPC92429
Rev 3, 05/2005
Freescale Semiconductor
Technical Data
Freescale Semiconductor, Inc., 2005. All rights reserved.
400 MHz Low Voltage PECL
Clock Synthesizer
The MPC92429 is a 3.3 V compatible, PLL based clock synthesizer targeted
for high performance clock generation in mid-range to high-performance
telecom, networking and computing applications. With output frequencies from
25 MHz to 400 MHz and the support of differential PECL output signals the
device meets the needs of the most demanding clock applications.
Features
25 MHz to 400 MHz synthesized clock output signal
Differential PECL output
LVCMOS compatible control inputs
On-chip crystal oscillator for reference frequency generation
3.3 V power supply
Fully integrated PLL
Minimal frequency overshoot
Serial 3-wire programming interface
Parallel programming interface for power-up
32-lead LQFP and 28-PLCC packaging
32-lead and 28-lead Pb-free package available
SiGe Technology
Ambient temperature range 0
°C to +70°C
Pin and function compatible to the MC12429 and MPC9229
Functional Description
The internal crystal oscillator uses the external quartz crystal as the basis of
its frequency reference. The frequency of the internal crystal oscillator is divided
by 16 and then multiplied by the PLL. The VCO within the PLL operates over a range of 800 to 1600 MHz. Its output is scaled by
a divider that is configured by either the serial or parallel interfaces. The crystal oscillator frequency fXTAL, the PLL feedback-
divider M and the PLL post-divider N determine the output frequency.
The feedback path of the PLL is internal. The PLL adjusts the VCO output frequency to be 4 x M times the reference frequency
by adjusting the VCO control voltage. Note that for some values of M (either too high or too low) the PLL will not achieve phase
lock. The PLL will be stable if the VCO frequency is within the specified VCO frequency range (800 to 1600 MHz). The M-value
must be programmed by the serial or parallel interface.
The PLL post-divider N is configured through either the serial or the parallel interfaces, and can provide one of four division
ratios (1, 2, 4, or 8). This divider extends performance of the part while providing a 50% duty cycle. The output driver is driven
differentially from the output divider, and is capable of driving a pair of transmission lines terminated 50
to VCC – 2.0 V. The
positive supply voltage for the internal PLL is separated from the power supply for the core logic and output drivers to minimize
noise induced jitter.
The configuration logic has two sections: serial and parallel. The parallel interface uses the values at the M[8:0] and N[1:0]
inputs to configure the internal counters. It is recommended on system reset to hold the P_LOAD input LOW until power becomes
valid. On the LOW-to-HIGH transition of P_LOAD, the parallel inputs are captured. The parallel interface has priority over the
serial interface. Internal pullup resistors are provided on the M[8:0] and N[1:0] inputs prevent the LVCMOS compatible control
inputs from floating.
The serial interface centers on a fourteen bit shift register. The shift register shifts once per rising edge of the S_CLOCK input.
The serial input S_DATA must meet setup and hold timing as specified in the AC Characteristics section of this document. The
configuration latches will capture the value of the shift register on the HIGH-to-LOW edge of the S_LOAD input. See PROGRAM-
MING INTERFACE for more information. The TEST output reflects various internal node values, and is controlled by the T[2:0]
bits in the serial data stream. In order to minimize the PLL jitter, it is recommended to avoid active signal on the TEST output.
MPC92429
400 MHZ LOW VOLTAGE
CLOCK SYNTHESIZER
FA SUFFIX
32-LEAD LQFP PACKAGE
CASE 873A-03
AC SUFFIX
32-LEAD LQFP PACKAGE
Pb-FREE PACKAGE
CASE 873A-03
EI SUFFIX
28-LEAD PLCC PACKAGE
Pb-FREE PACKAGE
CASE 776-02
FN SUFFIX
28-LEAD PLCC PACKAGE
CASE 776-02
相關PDF資料 |
PDF描述 |
|---|---|
| MPC92429ACR2 | 400 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| MPC92429FN | 400 MHz, OTHER CLOCK GENERATOR, PQCC28 |
| MPC92429EIR2 | 400 MHz, OTHER CLOCK GENERATOR, PQCC28 |
| MPC92432AER2 | 1360 MHz, OTHER CLOCK GENERATOR, PQFP48 |
| MPC92432FAR2 | 1360 MHz, OTHER CLOCK GENERATOR, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC92429FN | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:400 MHz Low Voltage PECL Clock Synthesizer |
| MPC92432 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:1360 MHz Dual Output LVPECL Clock Synthesizer |
| MPC92432AE | 功能描述:時鐘合成器/抖動清除器 FSL 1360MHz Dual Out put LVPECL Clock Syn RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC92432AER2 | 功能描述:時鐘合成器/抖動清除器 FSL 1360MHz Dual Out put LVPECL Clock Syn RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC92432FA | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:1360 MHz Dual Output LVPECL Clock Synthesizer |
發布緊急采購，3分鐘左右您將得到回復。