- 您現在的位置：買賣IC網 > PDF目錄25628 > MPC8547VUATJB (FREESCALE SEMICONDUCTOR INC) 32-BIT, 1200 MHz, MICROPROCESSOR, CBGA783 PDF資料下載
參數資料
| 型號： | MPC8547VUATJB |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, 1200 MHz, MICROPROCESSOR, CBGA783 |
| 封裝： | 29 X 29 MM, 1 MM PITCH, FLIP CHIP, LEAD FREE, CERAMIC, BGA-783 |
| 文件頁數： | 36/142頁 |
| 文件大小： | 1504K |
| 代理商： | MPC8547VUATJB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁
MPC8548E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5
130
Freescale Semiconductor
System Design Information
21.4
SerDes Block Power Supply Decoupling Recommendations
The SerDes block requires a clean, tightly regulated source of power (SVDD and XVDD) to ensure low
jitter on transmit and reliable recovery of data in the receiver. An appropriate decoupling scheme is
outlined below.
Only surface mount technology (SMT) capacitors should be used to minimize inductance. Connections
from all capacitors to power and ground should be done with multiple vias to further reduce inductance.
First, the board should have at least 10
× 10-nF SMT ceramic chip capacitors as close as possible
to the supply balls of the device. Where the board has blind vias, these capacitors should be placed
directly below the chip supply and ground connections. Where the board does not have blind vias,
these capacitors should be placed in a ring around the device as close to the supply and ground
connections as possible.
Second, there should be a 1-F ceramic chip capacitor from each SerDes supply (SVDD and
XVDD) to the board ground plane on each side of the device. This should be done for all SerDes
supplies.
Third, between the device and any SerDes voltage regulator there should be a 10-F, low
equivalent series resistance (ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT
tantalum chip capacitor. This should be done for all SerDes supplies.
21.5
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. All unused active low inputs should be tied to VDD, TVDD, BVDD, OVDD, GVDD, and LVDD, as
required. All unused active high inputs should be connected to GND. All NC (no-connect) signals must
remain unconnected. Power and ground connections must be made to all external VDD, TVDD, BVDD,
OVDD, GVDD, LVDD, and GND pins of the device.
21.6
Pull-Up and Pull-Down Resistor Requirements
The MPC8548E requires weak pull-up resistors (2–10 k
Ω is recommended) on open drain type pins
including I2C pins and PIC (interrupt) pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 62. Care must be taken to ensure that these pins are maintained at a valid deasserted
state under normal operating conditions as most have asynchronous behavior and spurious assertion will
give unpredictable results.
The following pins must not be pulled down during power-on reset: TSEC3_TXD[3], HRESET_REQ,
TRIG_OUT/READY/QUIESCE, MSRCID[2:4], ASLEEP. The DMA_DACK[0:1], and TEST_SEL/
TEST_SEL pins must be set to a proper state during POR configuration. Refer to the pinlist table of the
individual device for more details
Refer to the PCI 2.2 specification for all pull ups required for PCI.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC8548CPXATJ | 32-BIT, 1200 MHz, MICROPROCESSOR, PBGA783 |
| MPC8548CVUAQGB | 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA783 |
| MPC8548CVUATGB | 32-BIT, 1200 MHz, MICROPROCESSOR, CBGA783 |
| MPC8548CVUAVJA | 32-BIT, 1500 MHz, MICROPROCESSOR, CBGA783 |
| MPC8548ECVUAQJ | 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA783 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC8547VUAUJ | 功能描述:微處理器 - MPU PQ38 8548 PB-FREE RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC8548CDS | 制造商:Freescale Semiconductor 功能描述:CDS DEV TOOLS FOR 8548 制造商:Freescale Semiconductor 功能描述:CDS DEV TOOLS FOR 8548 - Bulk 制造商:Freescale Semiconductor 功能描述:DEV TOOLS CDS FOR 8548 制造商:Freescale Semiconductor 功能描述:KIT MPC8548 CONFIG DEV SYSTEM |
| MPC8548CDS | 制造商:Freescale Semiconductor 功能描述:CDS DEV TOOLS FOR 8548 |
| MPC8548CHXAQG | 功能描述:微處理器 - MPU PQ38 8548 PB-FREE -40C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC8548CPXAQGB | 功能描述:微處理器 - MPU FG PQ38 8548 RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
發布緊急采購，3分鐘左右您將得到回復。