- 您現在的位置：買賣IC網 > PDF目錄4068 > MPC8248CZQTIEA (Freescale Semiconductor)IC MPU POWERQUICC II 516-PBGA PDF資料下載
參數資料
| 型號： | MPC8248CZQTIEA |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 8/61頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MPU POWERQUICC II 516-PBGA |
| 標準包裝： | 40 |
| 系列： | MPC82xx |
| 處理器類型： | 32-位 MPC82xx PowerQUICC II |
| 速度： | 400MHz |
| 電壓： | 1.5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 516-BBGA |
| 供應商設備封裝： | 516-FPBGA（27x27） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
MPC8272 PowerQUICC II Family Hardware Specifications, Rev. 3
16
Freescale Semiconductor
Thermal Characteristics
4.4
Estimation Using Simulation
When the board temperature is not known, a thermal simulation of the application is needed. The simple
two-resistor model can be used with the thermal simulation of the application, or a more accurate and
complex model of the package can be used in the thermal simulation.
4.5
Experimental Determination
To determine the junction temperature of the device in the application after prototypes are available, the
thermal characterization parameter (
ΨJT) can be used to determine the junction temperature with a
measurement of the temperature at the top center of the package case using the following equation:
TJ = TT + (ΨJT × PD)
where:
Ψ
JT = thermal characterization parameter
TT = thermocouple temperature on top of package
PD = power dissipation in package
The thermal characterization parameter is measured per JEDEC JESD51-2 specification using a 40-gauge
type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned
so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over 1 mm of wire extending from the junction. The thermocouple wire is
placed flat against the case to avoid measurement errors caused by cooling effects of the thermocouple
wire.
4.6
Layout Practices
Each VDD and VDDH pin should be provided with a low-impedance path to the board’s power supplies.
Each ground pin should likewise be provided with a low-impedance path to ground. The power supply pins
drive distinct groups of logic on chip. The VDD and VDDH power supplies should be bypassed to ground
using bypass capacitors located as close as possible to the four sides of the package. For filtering high
frequency noise, a capacitor of 0.1uF on each VDD and VDDH pin is recommended. Further, for medium
frequency noise, a total of 2 capacitors of 47uF for VDD and 2 capacitors of 47uF for VDDH are also
recommended. The capacitor leads and associated printed circuit traces connecting to chip VDD, VDDH
and ground should be kept to less than half an inch per capacitor lead. Boards should employ separate inner
layers for power and GND planes.
All output pins on the SoC have fast rise and fall times. Printed circuit (PC) trace interconnection length
should be minimized to minimize overdamped conditions and reflections caused by these fast output
switching times. This recommendation particularly applies to the address and data buses. Maximum PC
trace lengths of six inches are recommended. Capacitance calculations should consider all device loads as
well as parasitic capacitances due to the PC traces. Attention to proper PCB layout and bypassing becomes
especially critical in systems with higher capacitive loads because these loads create higher transient
currents in the VDD and GND circuits. Pull up all unused inputs or signals that will be inputs during reset.
Special care should be taken to minimize the noise levels on the PLL supply pins.
相關PDF資料 |
PDF描述 |
|---|---|
| ABB92DHAT-S250 | CONN EDGECARD 184POS R/A .050 SL |
| CS80C286-16 | IC CPU 16BIT 5V 16MHZ 68-PLCC |
| ACB90DHAR | CONN EDGECARD 180PS R/A .050 DIP |
| MPC857TZQ66B | IC MPU PWRQUICC 66MHZ 357-PBGA |
| ABB95DHAS | CONN EDGECARD 190PS R/A .050 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC8248VR | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC8272 PowerQUICC II Family Hardware Specifications |
| MPC8248VRB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC II⑩ Family Hardware Specifications |
| MPC8248VRE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC II⑩ Family Hardware Specifications |
| MPC8248VRI | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC II⑩ Family Hardware Specifications |
| MPC8248VRM | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC II⑩ Family Hardware Specifications |
發布緊急采購，3分鐘左右您將得到回復。