- 您現在的位置：買賣IC網 > PDF目錄385630 > MP39 (APEX MICROTECHNOLOGY CORP) POWER OPERATIONAL AMPLIFIER PDF資料下載
參數資料
| 型號： | MP39 |
| 廠商： | APEX MICROTECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | POWER OPERATIONAL AMPLIFIER |
| 中文描述： | OP-AMP, 10000 uV OFFSET-MAX, 2 MHz BAND WIDTH, DMA30 |
| 封裝： | DIP-30 |
| 文件頁數： | 4/4頁 |
| 文件大?。?/td> | 257K |
| 代理商： | MP39 |
APEX MICROTECHNOLOGY CORPORATION TELEPHONE (520) 690-8600 FAX (520) 888-3329 ORDERS (520) 690-8601 EMAIL prodlit@apexmicrotech.com
4
GENERAL
Please read Application Note 1 "General Operating Con-
siderations" which covers stability, supplies, heat sinking,
mounting, current limit, SOA interpretation, and specification
interpretation. Visit www.apexmicrotech.com for design tools
that help automate tasks such as calculations for stability,
internal power dissipation, current limit; heat sink selection;
Apex’s complete Application Notes library; Technical Seminar
Workbook; and Evaluation Kits.
CURRENT LIMIT
The two current limit sense lines are to be connected directly
across the current limit sense resistor. For the current limit
to work correctly pin 24 must be connected to the amplifier
output side and pin 23 connected to the load side of the current
limit resistor, R
, as shown in Figure 1. This connection will
bypass any parasitic resistances, Rp, formed by sockets and
solder joints as well as internal amplifier losses. The current
limiting resistor may not be placed anywhere in the output
circuit except where shown in Figure 1.
The value of the current limit resistor can be calculated as
follows:
R
CL
=
.7
I
LIMIT
BOOST OPERATION
With the V
feature the small signal stages of the amplifier
are operated at higher supply voltages than the amplifier's high
current output stage. +V
(pins 12-14) and –V
(pins 18-20)
are connected to the high current output stage. An additional
10V on the V
pins is sufficient to allow the small signal stages
to drive the output transistors into saturation and improve the
output voltage swing for extra efficient operation when required.
When close swing to the supply rails is not required the +V
B
and +V
S
pins must be strapped together as well as the –V
B
and –V
pins. The boost voltage pins must not be at a voltage
lower than the V
S
pins.
BYPASSING
Proper bypassing of the power supply pins is crucial for proper
operation. Bypass the ±Vs pins with a aluminum electrolytic
capacitor with a value of at least 10μF per amp of expected
output current. In addition a .47μF to 1μF ceramic capacitor
should be placed in parallel with each aluminum electrolytic
capacitor. Both of these capacitors have to be placed as close
to the power supply pins as physically possible. If not connected
to the Vs pins (See BOOST OPERATION) the V
pins should
also be bypassed with a .47μF to 1μF ceramic capacitor.
USING THE IQ PIN FUNCTION
Pin 25 (Iq) can be tied to pin 6 (Cc1) to eliminate the class
AB biasing current from the output stage. Typically this would
remove 1-4 mA of quiescent current. The resulting decrease
in quiescent power dissipation may be important in some
applications. Note that implementing this option will raise the
output impedance of the amplifier and increase crossover
distortion as well.
COMPENSATION
The external compensation components C
and R
are con-
nected to pins 4 and 6. Unity gain stability can be achieved at
any compensation capacitance greater than 470 pF with at
least 60 degrees of phase margin. At higher gains more phase
shift can be tolerated in most designs and the compensation
capacitance can accordingly be reduced, resulting in higher
bandwidth and slew rate.
APPLICATION REFERENCES
For additional technical information please refer to the fol-
lowing application notes.
AN 1
General Operating Considerations
AN 11
Thermal Techniques
AN 38
Loop Stability with Reactive Loads
MP39U REV G JANUARY 2005 2005 Apex Microtechnology Corp.
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
MP39 MP39A
相關PDF資料 |
PDF描述 |
|---|---|
| MP39A | POWER OPERATIONAL AMPLIFIER |
| MPD-1 | Phase Detectors 1000mV DC output , + 7dBmRF |
| MPD-2 | Phase Detectors 1000mV DC output , + 7dBmRF |
| MPD-21 | Phase Detectors 1000mV DC output , + 7dBmRF |
| MPD100 | STABISTORS Also, Tight Tolerance |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP3900DK-LF-P | 功能描述:開關變換器、穩壓器與控制器 10V Gate Drive Boost Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP3900DK-LF-Z | 功能描述:開關變換器、穩壓器與控制器 10V Gate Drive Boost Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP3908DK-LF-P | 功能描述:開關變換器、穩壓器與控制器 High Efficiency Sync Boost Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP3908DK-LF-Z | 功能描述:開關變換器、穩壓器與控制器 High Efficiency Sync Boost Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP3910GK | 功能描述:Boost, Flyback, Forward Converter, SEPIC Regulator Positive, Isolation Capable Output Step-Up, Step-Up/Step-Down DC-DC Controller IC 10-MSOP 制造商:monolithic power systems inc. 系列:- 包裝:管件 零件狀態:有效 輸出類型:晶體管驅動器 功能:升壓，升壓/降壓 輸出配置:正，可提供隔離 拓?fù)?升壓，反激式，正向轉換器，SEPIC 輸出數:1 輸出階段:1 電壓 - 電源（Vcc/Vdd）:7 V ~ 35 V 頻率 - 開關:30kHz ~ 400kHz 占空比（最大）:0.95 同步整流器:無 時鐘同步:是 串行接口:- 控制特性:使能，頻率控制，軟啟動 工作溫度:-40°C ~ 125°C （TJ） 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:10-MSOP 標準包裝:50 |
發布緊急采購，3分鐘左右您將得到回復。