- 您現在的位置：買賣IC網 > PDF目錄224390 > MP2482DN (MONOLITHIC POWER SYSTEMS INC) 9 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | MP2482DN |
| 廠商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 9 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | MS-012BA, SOIC-8 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 350K |
| 代理商： | MP2482DN |
MP2482 – 5A, 30V, 420KHZ STEP-DOWN CONVERTER
MP2482 Rev.1.2
www.MonolithicPower.com
7
10/22/2009
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2009 MPS. All Rights Reserved.
Enable/Synch Control
The MP2482 has a dedicated Enable/Synch
control pin (EN/SYNC). By pulling it high or low,
the IC can be enabled and disabled by EN. Tie
EN to VIN for automatic start up. To disable the
part, EN must be pulled low for at least 5s.
The MP2482 can be synchronized to external
clock range from 300KHz up to 1.5MHz through
the EN/SYNC pin. The internal clock rising
edge is synchronized to the external clock rising
edge.
Under-Voltage Lockout (UVLO)
Under-voltage lockout (UVLO) is implemented
to protect the chip from operating at insufficient
supply voltage. The MP2482 UVLO comparator
monitors the output voltage of the internal
regulator, BYPASS. The UVLO rising threshold
is about 4.0V while its falling threshold is about
3.2V.
Internal Soft-Start
The soft-start is implemented to prevent the
converter output voltage from overshooting
during startup. When the chip starts, the
internal circuitry generates a soft-start voltage
(SS) ramping up from 0V to 1.2V. When it is
lower than the internal reference (REF), SS
overrides REF so the error amplifier uses SS as
the reference. When SS is higher than REF,
REF regains control.
Over-Current-Protection and Hiccup
The MP2482 has cycle-by-cycle over current
limit when the inductor current peak value
exceeds the set current limit threshold.
Meanwhile, output voltage starts to drop until
FB is below the Under-Voltage(UV) threshold,
typically 30% below the reference. Once a UV
is triggered, the MP2482 enters hiccup mode to
periodically restart the part. This protection
mode is especially useful when the output is
dead-short to ground. The average short circuit
current is greatly reduced to alleviate the
thermal issue and to protect the regulator. The
MP2482 exits the hiccup mode once the over
current condition is removed.
Thermal Shutdown
Thermal shutdown is implemented to prevent
the chip from operating at exceedingly high
temperatures. When the silicon die temperature
is higher than 150
°C, it shuts down the whole
chip. When the temperature is lower than its
lower threshold, typically 140
°C, the chip is
enabled again.
Floating Driver and Bootstrap Charging
The floating power MOSFET driver is powered
by an external bootstrap capacitor. This floating
driver has its own UVLO protection. This
UVLO’s rising threshold is 2.2V with a
hysteresis of 150mV. The bootstrap capacitor
voltage is regulated internally (Figure 2). Even
at light load condition, as long as VIN is 3V
higher than VOUT, C4 will have enough voltage
provided by VIN through D2, M2, C4, L1 and C2.
If (VIN-VSW) is more than 5V, U2 will regulate M2
to maintain a 5V BST voltage across C4.
--
+
--
+
VIN
5V
U2
D2
M2
BST
SW
C4
C2
L1
VOUT
Figure 2—Internal Bootstrap Charging Circuit
Startup and Shutdown
If both VIN and EN are higher than their
appropriate thresholds, the chip starts. The
reference block starts first, generating stable
reference voltage and currents, and then the
internal regulator is enabled. The regulator
provides stable supply for the remaining
circuitries.
Three events can shut down the chip: EN low,
VIN low and thermal shutdown. In the shutdown
procedure, the signaling path is first blocked to
avoid any fault triggering. The COMP voltage
and the internal supply rail are then pulled down.
The floating driver is not subject to this
shutdown
command.
相關PDF資料 |
PDF描述 |
|---|---|
| MP5010GN | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.22 V, PBCY2 |
| MP6-6131022R | 10 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| MP6-6131522R | 15 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| MP6-6132022R | 20 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| MP6-6132522R | 25 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP2482DN-LF | 功能描述:開關變換器、穩壓器與控制器 6A 30V 420kHz Nonsync Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP2482DN-LF-Z | 功能描述:開關變換器、穩壓器與控制器 6A 30V 420kHz Nonsync Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP24830HS-LF | 功能描述:LED照明驅動器 LED driver for TV LED backlight RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MP24830HS-LF-Z | 制造商:Monolithic Power Systems 功能描述:BUCK BOOST POWER LEVERAGE LED DRIVER FOR TV LED BACKLIGHT - Tape and Reel 制造商:Monolithic Power Systems 功能描述:LED driver for TV LED backlight |
| MP24833GN | 制造商:Monolithic Power Systems 功能描述:3A, 55V LED DRIVER WITH INTEGRATED FET - Rail/Tube 制造商:Monolithic Power Systems 功能描述:2.5A, 55V, Prgrmbl Freq White LED Drvr |
發布緊急采購，3分鐘左右您將得到回復。