- 您現在的位置：買賣IC網 > PDF目錄183286 > MP2371DG-Z (MONOLITHIC POWER SYSTEMS INC) SWITCHING REGULATOR, DSO8 PDF資料下載
參數資料
| 型號： | MP2371DG-Z |
| 廠商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, DSO8 |
| 封裝： | 2 X 2 MM, MO-229VCCD-3, QFN-8 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 650K |
| 代理商： | MP2371DG-Z |
MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER
MP2371 Rev. 1.0
www.MonolithicPower.com
7
5/26/2008
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2008 MPS. All Rights Reserved.
APPLICATION INFORMATION
Setting Output Voltage
The external resistor divider is used to set the
output voltage (see the schematic on front
page). The feedback resistor R1 also sets the
feedback loop bandwidth with the internal
compensation capacitor (see Figure 1). R2 can
be determined by:
1
V
81
.
0
V
1
R
2
R
OUT
=
Table 1—Resistor Selection for Common
Output Voltages
VOUT (V)
R1 (k)
R2 (k)
1.8
80.6 (1%)
64.9 (1%)
2.5
49.9 (1%)
23.7 (1%)
3.3
49.9 (1%)
16.2 (1%)
5
49.9 (1%)
9.53 (1%)
Selecting the Inductor
A 1H to 10H inductor with a DC current rating
of at least 25% percent higher than the
maximum load current is recommended for
most applications. For highest efficiency, the
inductor’s DC resistance should be less than
200m. For most designs, the required
inductance value can be derived from the
following equation.
OUT
IN
OUT
IN
L
OSC
V(V
V
)
L1
VI
f
×
=
× ×
Where IL is the inductor ripple current.
Choose an inductor with a rating current of
approximately 30% higher than the maximum
load current if the maximum load current is
≥1.8A. The maximum inductor peak current is
calculated from:
2
I
L
LOAD
)
MAX
(
L
+
=
Under light load conditions below 100mA, a
larger inductance is recommended for improved
efficiency. See Table 2 for suggested inductors.
Selecting the Input Capacitor
The input capacitor reduces the surge current
drawn from the input and the switching noise from
the device. The input capacitor impedance at the
switching frequency should be less than the input
source impedance to prevent high frequency
switching current from passing through the input.
Ceramic capacitors with X5R or X7R dielectrics
are highly recommended because of their low
ESR and small temperature coefficients. For most
applications, a 10F capacitor is sufficient.
Selecting the Output Capacitor
The output capacitor keeps output voltage ripple
small and ensures loop stability. The output
capacitor impedance should be low at the
switching frequency. Ceramic capacitors with
X5R or X7R dielectrics are recommended for their
low ESR characteristics. For most applications, a
22F ceramic capacitor will be sufficient.
PCB Layout Guide
PCB layout is very important to achieve stable
operation. Please follow these guidelines and
take Figure2 for references.
1) Keep the path of switching current short
and minimize the loop area formed by Input
cap, high-side MOSFET and schottky diode.
2) Keep the connection of schottky diode
between SW pin and input power ground
as short and wide as possible.
3) Ensure all feedback connections are short
and direct. Place the feedback resistors
and compensation components as close to
the chip as possible.
4) Route SW away from sensitive analog
areas such as FB.
5) Connect IN, SW, and especially GND
respectively to a large copper area to cool
the chip to improve thermal performance
and long-term reliability. For single layer,
do not solder exposed pad of the IC.
相關PDF資料 |
PDF描述 |
|---|---|
| MP2A-470-R | 1 ELEMENT, 47 uH, MOLY PERMALLOY POWDER-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| MP3510W | 35 A, 1000 V, SILICON, BRIDGE RECTIFIER DIODE |
| MP351 | 20 mA, 45 V, 2 CHANNEL, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-52 |
| MP350 | 20 mA, 25 V, 2 CHANNEL, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-52 |
| MP352A | 20 mA, 45 V, 2 CHANNEL, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP2377DN-LF-Z | 制造商:Monolithic Power Systems 功能描述:MONOLITHIC STEP-DOWN SWITCH MODE CONVERTER - Tape and Reel |
| MP2378DS-LF | 功能描述:開關變換器、穩壓器與控制器 2A 30V 385KHz Step-Down Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP2378DS-LF-Z | 功能描述:開關變換器、穩壓器與控制器 2A 30V 385KHz Step-Down Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP2378RA | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述: |
| MP2380DN-LF | 功能描述:開關變換器、穩壓器與控制器 5A 21V 600KHz Nonsync Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。