- 您現在的位置：買賣IC網 > PDF目錄383630 > MP03XXX330-12 (Dynex Semiconductor Ltd.) Phase Control Dual SCR, SCR/Diode Modules PDF資料下載
參數資料
| 型號： | MP03XXX330-12 |
| 廠商： | Dynex Semiconductor Ltd. |
| 英文描述： | Phase Control Dual SCR, SCR/Diode Modules |
| 中文描述： | 相位控制雙可控硅，SCR /二極管模塊 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 137K |
| 代理商： | MP03XXX330-12 |
3/10
MP03 XXX 330 Series
Symbol
Parameter
Conditions
Gate non-trigger voltage
V
3.0
0.25
Typ.
mA
V
V
GD
Gate trigger voltage
150
V
GT
I
GT
Gate trigger current
At V
DRM
T
case
= 25
o
C
V
DRM
= 5V, T
case
= 25
o
C
V
DRM
= 5V, T
case
= 25
o
C
-
-
-
V
30
0.25
V
V
RGM
Peak reverse gate voltage
V
5.0
-
A
-
-
-
10
I
FGM
Peak forward gate current
Peak forward gate voltage
V
FGM
V
FGN
Peak forward gate voltage
Anode positive with respect to cathode
Anode negative with respect to cathode
Anode positive with respect to cathode
P
GM
P
G(AV)
Peak gate power
Mean gate power
t
p
= 25
μ
s
-
-
100
5
W
W
Max.
Units
I
Adequate heatsinking is required to maintain the base
temperature at 75
o
C if full rated current is to be achieved. Power
dissipation may be calculated by use of V
and r
information in
accordance with standard formulae. We can provide assistance
with calculations or choice of heatsink if required.
I
The heatsink surface must be smooth and flat; a surface finish
of N6 (32
μ
in) and a flatness within 0.05mm (0.002") are
recommended.
I
Immediately prior to mounting, the heatsink surface should be
lightly scrubbed with fine emery, Scotch Brite or a mild chemical
etchant and then cleaned with a solvent to remove oxide build up
and foreign material. Care should be taken to ensure no foreign
particles remain.
I
An even coating of thermal compound (eg. Unial) should be
applied to both the heatsink and module mounting surfaces. This
should ideally be 0.05mm (0.002") per surface to ensure optimum
thermal performance.
I
After application of thermal compound, place the module squarely
over the mounting holes, (or 'T' slots) in the heatsink. Using a
torque wrench, slowly tighten the recommended fixing bolts at
each end, rotating each in turn no more than 1/4 of a revolution at
a time. Continue until the required torque of 5Nm (44lb.ins) is
reached at both ends.
I
It is not acceptable to fully tighten one fixing bolt before starting
to tighten the others. Such action may DAMAGE the module.
GATE TRIGGER CHARACTERISTICS AND RATINGS
MOUNTING RECOMMENDATIONS
Examples:
MP03 HBP330 - 08
MP03 HBN330 - 12
MP03 HBT330 - 08
Part number is made up of as follows:
MP03 HBT 330 -10
MP
03
HBT = Circuit configuration code (see "circuit options" - front page)
330
= Nominal average current rating at T
case
= 75
o
C
10
= V
RRM
/100
= Pressure contact module
= Outline type
NOTE: Diode ratings and characteristics are comparable with the SCR in types HBP or HBN
Types HBP or HBN can also be supplied with diode polarity reversed, to special order.
ORDERING INSTRUCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| MP03XXX330 | Phase Control Dual SCR, SCR/Diode Modules |
| MP04DD810-30-W2 | Dual Rectifier Diode Water Cooled Module Preliminary Information |
| MP04DD810-30-W3 | Dual Rectifier Diode Water Cooled Module Preliminary Information |
| MP04DD810-30-W3A | Dual Rectifier Diode Water Cooled Module Preliminary Information |
| MP04DD810 | Dual Rectifier Diode Water Cooled Module Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP03XXX360 | 制造商:DYNEX 制造商全稱:Dynex Semiconductor 功能描述:Dual Thyristor, Thyristor/Diode Module |
| MP04 | 制造商:CHENG-YI 制造商全稱:CHENG-YI ELECTRONIC CO., LTD. 功能描述:15/25/35 AMPS. SILICON BRIDGE RECTIFIERS |
| MP040 | 功能描述:晶體 4.00000 MHz 20pF RoHS:否 制造商:AVX 頻率:26 MHz 容差: 頻率穩定性:50 PPM 負載電容:8 pF 端接類型:SMD/SMT 封裝 / 箱體:1210 (3225 metric) 工作溫度范圍:- 40 C to + 150 C 尺寸:2.5 mm W x 3.2 mm L x 0.85 mm H 封裝:Reel |
| MP-040040-25-8A | 制造商:TE Connectivity 功能描述:Labels Thermal Transfer Printable Label Polyester Matte Silver 4x4mm |
| MP0407 | 制造商:Cooper Crouse-Hinds 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。