
MAD00059BEM
MN101C79A
Timer counter 8 : 16 bit × 1
(square-wave/16-bit PWM output [duty continuous variable], event count, pulse width measurement, input capture)
(square-wave/PWM output to large current terminal P53 possible)
Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1,
1/2, 1/4, 1/16 of external clock input frequency
Interrupt source ........... coincidence with compare register 8 (2 lines), input capture register
Timer counters 7, 8 can be cascade-connected.
(square-wave output, PWM input capture, pluse width measurement is possible as a 32-bit timer.)
Time base timer (one-minute count setting)
Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency
Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768, of clock source frequency
Watchdog timer
Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency
Serial interface
Serial 0 : synchronous type/UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of OSC
oscillation clock frequency, external clock
Serial 1 : synchronous type/UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of OSC
oscillation clock frequency, external clock
Serial 3 : synchronous type/single-master IC × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3; 1/2, 1/4, 1/16, 1/32 of OSC
oscillation clock frequency, external clock
Serial 4 : IC slave × 1 (Applicable for IC high-speed transfer mode, 7bit/10bit address setting, general call)
I/O Pins
I/O
35
Common use , Specied pull-up resistor available, Input/output selectable (bit unit)
A/D converter
10-bit × 4-ch. (with S/H)
Display control function
LCD
12 segments × 4 commons (static, 1/2, 1/3, or 1/4 duty)
(usable if VLCD ≤ VDD)
Special Ports
Buzzer output, remote control carrier signal output, high-current drive port
Electrical Charactreistics (Supply current)
Parameter
Symbol
Condition
Limit
Unit
min
typ
max
Operating supply current
IDD1
fosc = 4.25 MHz (fs = fosc / 2), VDD = 3 V
0.6
(1.3)
1.1
(2.2)
mA
IDD2
fx = 32 kHz (fs = fx / 2), VDD = 3 V
4 (46) 15 (90) A
Supply current at HALT
IDD3
fx = 32 kHz , VDD = 3 V, Ta = 25°C
2 (3) 5 (13)
A
IDD4
fx = 32 kHz , VDD = 3 V , Ta = –40°C to +85°C
10 (40) A
Supply current at STOP
IDD5
VDD = 3 V , Ta = 25°C
2 (3)
A
IDD6
VDD = 3 V , Ta = –40°C to +85°C
8 (30)
A
( ) : Flash memory built-in type