- 您現在的位置：買賣IC網 > PDF目錄369922 > MMSZ5247BT1 (MOTOROLA INC) Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode PDF資料下載
參數資料
| 型號： | MMSZ5247BT1 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 參考電壓二極管 |
| 英文描述： | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| 中文描述： | 17 V, 0.5 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| 封裝： | PLASTIC, CASE 425, 2 PIN |
| 文件頁數： | 6/7頁 |
| 文件大?。?/td> | 100K |
| 代理商： | MMSZ5247BT1 |
MMSZ5221BT1 Series
Motorola TVS/Zener Device Data
7-6
500 mW Leadless (SOD-123) Data Sheet
INFORMATION FOR USING THE SOD-123 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINTS FOR
SURFACE MOUNT APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must be
the correct size to ensure proper solder connection interface
between the board and the package.
The minimum recommended footprint for the SOD-123 is
shown at the right.
The SOD-123 package can be used on existing surface
mount boards which have been designed for the leadless 34
package style. The footprint compatibility makes conversion
from leadless 34 to SOD-123 straightforward.
éééé
éééé
éééé
éééé
éééé
mm
inches
0.91
0.036
1.22
0.048
2.36
0.093
4.19
0.165
Figure 11. Minimum Recommended Footprint
SOD-123 POWER DISSIPATION
The power dissipation of the SOD-123 is a function of the
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined by
TJ(max), the maximum rated junction temperature of the die,
R
θ
JA, the thermal resistance from the device junction to
ambient; and the operating temperature, TA. Using the values
provided on the data sheet for the SOD-123 package, PD can
be calculated as follows:
PD =
TJ(max) – TA
R
θ
JA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25
°
C, one can
calculate the power dissipation of the device which in this case
is 0.37 watts.
PD =150
°
C – 25
°
C
340
°
C/W
= 0.37 watts
The 340
°
C/W for the SOD-123 package assumes using
recommended footprint shown on FR-4 glass epoxy printed
circuit board. Another alternative is to use a ceramic substrate
or an aluminum core board such as Thermal Clad
. By using
an aluminum core board material such as Thermal Clad, the
power dissipation can be doubled using the same footprint.
GENERAL SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and soldering
should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the maximum
temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should be
allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相關PDF資料 |
PDF描述 |
|---|---|
| MMSZ5257BT1 | 3.3V, 133MHz Desktop PC 1:18 Output Clock Driver with Edge Rate Control |
| MMSZ5267BT1 | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| MMSZ5225BT1 | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| MMSZ5226BT1 | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| MMSZ5231BT1 | 100mA, 5.0V or Adjustable Output 1.23 to 30V, , Low Power Low Dropout Voltage Regulator with Error Flag output ; Package: 8 LEAD PDIP; No of Pins: 8; Container: Rail; Qty per Container: 50 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MMSZ5247BT1G | 功能描述:穩壓二極管 17V 500mW RoHS:否 制造商:Vishay Semiconductors 齊納電壓:12 V 電壓容差:5 % 電壓溫度系數:0.075 % / K 齊納電流: 功率耗散:3 W 最大反向漏泄電流:3 uA 最大齊納阻抗:7 Ohms 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AC 封裝:Reel |
| MMSZ5247B-V-GS08 | 功能描述:穩壓二極管 17 Volt 0.5 Watt 5% RoHS:否 制造商:Vishay Semiconductors 齊納電壓:12 V 電壓容差:5 % 電壓溫度系數:0.075 % / K 齊納電流: 功率耗散:3 W 最大反向漏泄電流:3 uA 最大齊納阻抗:7 Ohms 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AC 封裝:Reel |
| MMSZ5247B-V-GS18 | 功能描述:穩壓二極管 17 Volt 0.5 Watt 5% RoHS:否 制造商:Vishay Semiconductors 齊納電壓:12 V 電壓容差:5 % 電壓溫度系數:0.075 % / K 齊納電流: 功率耗散:3 W 最大反向漏泄電流:3 uA 最大齊納阻抗:7 Ohms 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AC 封裝:Reel |
| MMSZ5247C-E3-08 | 制造商:Vishay Intertechnologies 功能描述:Zener Diodes 17 Volt 0.5W 2% 制造商:Vishay Intertechnologies 功能描述:ZENER DIODE SOD123 |
| MMSZ5247C-G3-08 | 制造商:Vishay Intertechnologies 功能描述:Zener Diodes 17 Volt 0.5W 2% 制造商:Vishay Intertechnologies 功能描述:ZENER DIODE SOD123 |
發布緊急采購，3分鐘左右您將得到回復。