- 您現在的位置：買賣IC網 > PDF目錄98023 > MM908E622ACDWB/R2 (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 PDF資料下載
參數資料
| 型號： | MM908E622ACDWB/R2 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| 封裝： | 17.90 X 7.50 MM, 0.65 MM PITCH, PLASTIC, SOIC-54 |
| 文件頁數： | 25/66頁 |
| 文件大?。?/td> | 1277K |
| 代理商： | MM908E622ACDWB/R2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
908E622
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
POR— Power On Reset Bit
This read/write bit is set after power on. The bit is cleared
by writing a logic “1” to this location.
1 = Reset due to power on
0 = no power on reset
PINR— Reset Forced from External Reset Pin Bit
This read/write bit is set after a reset was forced on the
external reset RST_A pin. The bit is cleared by writing a logic
“1” to this location.
1 = reset source is external reset pin
0 = no external reset
WDR— Watch Dog Reset Bit
This read/write flag is set due to watchdog timeout or a
wrong watchdog timer reset. Clear WDR by writing a logic “1”
to WDR.
1 = reset source is watchdog
0 = no watchdog reset
HTR— High Temperature Reset Bit
This read/write bit is set if the chip temperature exceeds a
certain value. The bit is cleared by writing a logic “1” to this
location.
1 = reset due to high temperature condition
0 = no high temperature reset
LVR— Low Voltage Reset Bit
This read/write bit is set if the external VDD voltage coming
from the main voltage regulator falls below a certain value. Bit
is cleared by writing a logic “1” to this location.
1 = reset due to low voltage condition
0 = no low voltage reset
LINWF— LIN Wake-up Flag
This read/write bit is set if a bus activity was the case of an
wake-up. Bit is cleared by writing a logic “1” to this location.
1 = Wake-up due to bus activity
0 = no wake-up due to bus activity
L0WF— L0 Wake-up Flag
This read/write bit is set if a event on the L0 pin caused an
wake-up. Bit is cleared by writing a logic “1” to this location.
1 = Wake-up due to L0 pin
0 = no Wake-up due to L0 pin
ANALOG DIE INPUTS/OUTPUTS
LIN PHYSICAL LAYER
The LIN bus pin provides a physical layer for single-wire
communication in automotive applications. The LIN physical
layer is designed to meet the LIN physical layer specification.
The LIN driver is a low side MOSFET with internal current
limitation and thermal shutdown. An internal pull-up resistor
with a serial diode structure is integrated, so no external pull-
up components are required for the application in a slave
mode. The fall time from dominant to recessive, and the rise
time from recessive to dominant is controlled. The symmetry
between both slew rate controls is guaranteed.
The slew rate can be selected for optimized operation at
10 and 20kBit/s, as well as high baud rates for test and
programming. The slew rate can be adapted with 2 bits
SRS[1:0] in the System Control Register. The initial slew rate
is optimized for 20kBit/s.
The LIN pin offers high susceptibility immunity level from
external disturbance, guaranteeing communication during
external disturbance.
The LIN transmitter circuitry is enabled by setting the
PSON bit in the System Control Register (SYSCTL).
If the transmitter works in the current limitation region, the
LINCL bit in the System Status Register (SYSSTAT) is set
and the LIN transceiver is disabled after a certain time.
For improved performance and safe behavior when the
LIN bus shorts to Ground, or LIN bus leakage during low
power mode, the internal pull-up resistor on the LIN pin is
disconnected from VSUP and a small current source keeps
the LIN bus at recessive level. In case of a LIN bus short to
GND, this feature will reduce the current consumption in
STOP and SLEEP modes.
Register Name and Address: RSR - $0D
Bit7
6
5
4
3
2
1
Bit0
Read
POR
PINR
WDR
HTR
LVR
0
LINWF LOWF
Write
POR
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E624ACDWB/R | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E625ACDWB | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MMBD1010LT3 | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB |
| MMBD3000T1 | 0.2 A, SILICON, SIGNAL DIODE |
| MMBD1000LT3 | 0.2 A, SILICON, SIGNAL DIODE, TO-236AB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E622ACEK | 功能描述:8位微控制器 -MCU QUAD H-B TRIHS EC GLASS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E622ACPEK | 功能描述:IC QUAD HALF BRDG TRPL SW 54SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:- 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| MM908E622ACPEKR2 | 功能描述:8位微控制器 -MCU QUAD H-B, TRIHS, EC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E624 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:TRIPLE HIGH-SIDE SWITCH WITH EMBEDDED MCU AND LIN |
| MM908E624ACDWB | 功能描述:IC TRPL SWITCH MCU/LIN 54-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:- 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
發布緊急采購，3分鐘左右您將得到回復。