- 您現在的位置：買賣IC網 > PDF目錄45334 > MLX90308CABLUD MICROCONTROLLER, UUC PDF資料下載
參數資料
| 型號： | MLX90308CABLUD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, UUC |
| 封裝： | DIE |
| 文件頁數： | 4/24頁 |
| 文件大?。?/td> | 724K |
| 代理商： | MLX90308CABLUD |
MLX90308CAB
Programmable Sensor Interface
MLX90308CAB Programmable Sensor Interface
Page 12
Rev 2.0 11/October/00
Figure 5.
Alarm Function
OUTPUT
Output
Input Signal
MLX90308
Low
Output
Low
Trigger
High
Trigger
High
Output
Selected input
MUX Value
TPO
0010
IAO
0110
GNO
0000
VMO
0011
IO1
0100
IO2
0101
Table 7. Alarm Source Bit Definition
Figure 6.
Alarm & Steering
Source Points
VMO
CMO
CMN
TSTB
VM
Gain
CM
Offset
Power Supply
Regulation
Temp
Sense
& Amp
Bidirectional
I/O
ADC
&
DAC
UART
Microcontroller
Core, Memory,
EEPROM
Reset,Test,&
Oscillator
O F C
F L T
VDD1
FET V D D
G N D
COMS
IO2
IO1
TMP
VBN
VBP
IAO
GNO
TPO
I.8 Alarm Option
This option allows controlling the low and high limits
of the output (See Figure 5.). The output level is set
when the output tries to exceed the programmed
limits. Five bytes are reserved for this option. The
first byte is the low trigger limit and the second the
low output. The third and fourth bytes are used for
the high limit and the output. The fifth byte is the
alarm control, used to select the alarm input. The
different
levels
are
programmed
as
eight
bit
numbers. These correspond to the 8 upper bits of the
10 bit signal measurement. When the alarm mode is
not used, all of the data is 0. The control code is
coded as shown in Table 7. The six possible signals
are listed below and are encoded on the 4 MSB’s of
byte 31 of the EEPROM.
IO1 & IO2
IO1 and IO2 are used in the alarm and level steering
modes. For custom firmware, they can be used for a
digital input, an analog input, or a digital output.
Figure 7. Level Steering
Function
IO1, IO2
Parameter
MLX90308
Level 1
1 -1
1 - 0
0 - 1
0 - 0
(I02,I01)
Level 2
Level 3
相關PDF資料 |
PDF描述 |
|---|---|
| MM3S05100 | 0.5 A, SILICON, SIGNAL DIODE |
| MM3S0560 | 0.5 A, SILICON, SIGNAL DIODE |
| MM3S0520 | 0.5 A, SILICON, SIGNAL DIODE |
| MM3S0540 | 0.5 A, SILICON, SIGNAL DIODE |
| MM54C163W | CMOS SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, CDFP16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MLX90308CCC | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:Programmable Sensor Interface |
| MLX90308CCCLW | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:Programmable Sensor Interface |
| MLX90308CCCUD | 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:Programmable Sensor Interface |
| MLX90308LDF | 制造商:MELEXIS 制造商全稱:Melexis Microelectronic Systems 功能描述:Programmable Sensor Interface |
| MLX90308LDF-DAA-000-RE | 制造商:Melexis Semiconductors 功能描述:IC SENSOR PROG INTERFACE 16SOIC |
發布緊急采購，3分鐘左右您將得到回復。