- 您現在的位置：買賣IC網 > PDF目錄45333 > ML9206-XXGS-K (OKI ELECTRIC INDUSTRY CO LTD) 16 X 37 DOTS FLUORESCENT DSPL CTRL, PDSO64 PDF資料下載
參數資料
| 型號： | ML9206-XXGS-K |
| 廠商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分類： | 顯示控制器 |
| 英文描述： | 16 X 37 DOTS FLUORESCENT DSPL CTRL, PDSO64 |
| 封裝： | 0.525 INCH, 0.80 MM PITCH, PLASTIC, SSOP-64 |
| 文件頁數： | 7/33頁 |
| 文件大?。?/td> | 356K |
| 代理商： | ML9206-XXGS-K |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Semiconductor
ML9206-xx
15/32
Data Transfer Method and Command Write Method
Display control command and data are written by an 8-bit serial transfer.
Write timing is shown in the figure below.
Setting the CS pin to "Low" level enables a data transfer.
Data is 8 bits and is sequentially input into the DA pin from LSB (LSB first).
As shown in the figure below, data is read by the shift register at the rising edge of the shift clock,
which is input into the CP pin. If 8-bit data is input, internal load signals are automatically
generated and data is written to each register and RAM.
Therefore it is not necessary to input load signals from the outside.
Setting the CS pin to "High" disables data transfer. Data input from the point when the CS pin
changes from "High" to "Low" is recognized in 8-bit units.
*
When data is written to RAM (DCRAM, ADRAM, CGRAM) continuously, addresses are
internally incremented automatically.
Therefore it is not necessary to specify the 1st byte to write RAM data for the 2nd and later
bytes.
Reset Function
Reset is executed when the RESET pin is set to "L", (when turning power on, for example) and
initializes all functions.
Initial status is as follows.
Address of each RAM .................. address "00"H
Data of each RAM ........................ All contents are undefined
General output port ..................... All general output ports go "Low"
Display digit .................................. 16 digits
Brightness adjustment ................. 0/256
All display lights ON or OFF ..... OFF mode
Segment output ............................ All segment outputs go "Low"
AD output ..................................... All AD outputs go "Low"
Please set again according to "Setting Flowchart" after reset.
tDOFF
B0
LSB
CS
CP
DA
B1 B2 B3 B4 B5 B6 B7
B0 B1 B2 B3 B4 B5 B6 B7
MSB
1st byte
LSB
MSB
2nd byte
When data is written to DCRAM* Command and address data
tCSH
B0 B1 B2 B3 B4 B5 B6 B7
LSB
MSB
2nd byte
Character code data of the
next address
Character code data
相關PDF資料 |
PDF描述 |
|---|---|
| ML9206-XXMB | 36 X 16 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PDSO64 |
| ML9206-XXGA | 36 X 16 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP64 |
| ML9207-01GP | 24 X 36 DOTS FLUORESCENT DSPL CTRL, PQFP80 |
| ML9207-XXGA | 24 X 36 DOTS FLUORESCENT DSPL CTRL, PQFP80 |
| ML9207-01GA | 24 X 36 DOTS FLUORESCENT DSPL CTRL, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML9207 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character × 24-Digit Display Controller/Driver with Character RAM |
| ML9207-XX | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character × 24-Digit Display Controller/Driver with Character RAM |
| ML9207-XXGA | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character 】 24-Digit Display Controller/Driver with Character RAM |
| ML9207-XXGP | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character × 24-Digit Display Controller/Driver with Character RAM |
| ML9208 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character X 16-Digit Display Controller/Driver with Character RAM |
發布緊急采購，3分鐘左右您將得到回復。