參數資料
型號: ML4861ES-6
英文描述: Low Voltage Boost Regulator
中文描述: 低電壓升壓穩壓器
文件頁數: 6/11頁
文件大小: 218K
代理商: ML4861ES-6
6
ML4861
100
1.0
3.0
I
O
2.0
200
300
400
500
0
L = 10μH
L = 15μH
L = 27μH
L = 56μH
V
IN
(V)
ML4861-3.3
100
1.0
3.0
4.0
I
O
2.0
200
300
400
500
0
L = 10μH
L = 15μH
L = 27μH
L = 56μH
ML4861-5.0
V
IN
(V)
100
1.0
3.0
4.0
I
O
2.0
200
300
400
500
0
L = 10μH
L = 15μH
L = 27μH
L = 56μH
ML4861-6.0
V
IN
(V)
5.0
6.0
Figure 5 shows efficiency under the conditions used to
create Figure 4. It can be seen that efficiency is mostly
independent of input voltage and is closely related to
inductor value. This illustrates the need to keep the
inductor value as high as possible to attain peak system
efficiency. As the inductor value goes down to 10μH, the
efficiency drops to between 70% and 75%. With 56μH,
the efficiency exceeds 90% and there is little room for
improvement. At values greater than 100μH, the operation
of the synchronous rectifier becomes unreliable because
the inductor current is so small that it is difficult for the
control circuitry to detect. The data used to generate
Figures 4 and 5 is provided in Table 1.
After the appropriate inductor value is chosen, it is
necessary to find the minimum inductor current rating
required. Peak inductor current is determined from the
following formula:
I
T
V
L
L PEAK
(
ON MAX
(
IN MAX
(
MIN
)
)
)
=
×
(3)
In the two cell application previously described, a
maximum input voltage of 3V would give a peak current
of 1.2A. When comparing various inductors, it is
important to keep in mind that suppliers use different
criteria to determine their ratings. Many use a
conservative current level, where inductance has dropped
to 90% of its normal level. In any case, it is a good idea to
try inductors of various current ratings with the ML4861 to
determine which inductor is the best choice. Check
efficiency and maximum output current, and if a current
probe is available, look at the inductor current to see if it
looks like the waveform shown in Figure 3. For additional
information, see Applications Note 29, “Choosing an
Inductor for Your ML4861 Application.”
Suitable inductors can be purchased from the following
suppliers:
Coilcraft
(708) 639-6400
Coiltronics
(407) 241-7876
Dale
(605) 665-9301
Sumida
(708) 956-0666
Figure 4. Output Current vs Input Voltage.
相關PDF資料
PDF描述
ML4869ES-3 Medium Current Boost Regulator with Load Disconnect
ML4869ES-5 Medium Current Boost Regulator with Load Disconnect
ML4870CS-3 High Current Boost Regulator with Load Disconnect
ML4870ES-3 High Current Boost Regulator with Load Disconnect
ML4870ES-5 High Current Boost Regulator with Load Disconnect
相關代理商/技術參數
參數描述
ML4861IS-3 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Low Voltage Boost Regulator
ML4861IS-5 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Low Voltage Boost Regulator
ML4861IS-6 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Low Voltage Boost Regulator
ML4862 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Battery Power ControllC
ML4863 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:High Efficiency Flyback Controller