- 您現在的位置：買賣IC網 > PDF目錄377971 > ML4861 (Fairchild Semiconductor Corporation) Low Voltage Drop Boost Regulator(低壓差升壓穩壓器) PDF資料下載
參數資料
| 型號： | ML4861 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Low Voltage Drop Boost Regulator(低壓差升壓穩壓器) |
| 中文描述： | 低壓降升壓穩壓器（低壓差升壓穩壓器） |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 118K |
| 代理商： | ML4861 |
ML4861
8
REV. 1.0 10/12/2000
INPUT CAPACITOR
Unless the input source is a very low impedance battery,
it will be necessary to decouple the input with a
capacitor with a value of between 47μF and 100μF. This
provides the benefits of preventing input ripple from
affecting the ML4861 control circuitry, and it also
improves efficiency by reducing I-squared R losses during
the charge and discharge cycles of the inductor. Again, a
low ESR capacitor (such as tantalum) is recommended.
REFERENCE CAPACITOR
Under some circumstances input ripple cannot be reduced
effectively. This occurs primarily in applications where
inductor currents are high, causing excess output ripple
due to “pulse grouping”, where the charge-discharge
pulses are not evenly spaced in time. In such cases it may
be necessary to decouple the reference pin (V
REF
) with a
small 10nF to 100nF ceramic capacitor. This is
particularly true if the ripple voltage at V
IN
is greater than
100mV.
SETTING THE
RESET
THRESHOLD
To use the
RESET
comparator as an input voltage
monitor, it is necessary to use an external resistor divider
tied to the DETECT pin as shown in the block diagram.
The resistor values R
A
and R
B
can be calculated using the
following equation:
V
R
(
R
R
IN MIN
(
A
B
B
)
.
)
=
×
+
0 2
(5)
The value of R
B
should be 100ky or less to minimize bias
current errors. R
A
is then found by rearranging the
equation:
R
R
V
A
B
IN MIN
(
.2
=
×
)
1
(6)
LAYOUT
Good PC board layout practices will ensure the proper
operation of the ML4861. Important layout considerations
include:
Use adequate ground and power traces or planes
Keep components as close as possible to the ML4861
Use short trace lengths from the inductor to the V
L
pin
and from the output capacitor to the V
OUT
pin
Use a single point ground for the ML4861 ground pins,
and the input and output capacitors
A sample PC board layout is shown in Figure 6.
TOP LAYER
BOTTOM LAYER
Figure 6. Sample PC Board Layout.
相關PDF資料 |
PDF描述 |
|---|---|
| ML4863 | High Efficiency Flyback Controller(高效回轉電源控制器) |
| ML4865CS-2 | High Voltage High Current Boost Regulator |
| ML4865 | High Voltage High Current Boost Regulator |
| ML4866 | 3.3V Output DC-DC Step-Down Converter(3.3V輸出的DC-DC步降變換器) |
| ML4869 | Medium Current Boost Regulator with Load Disconnect(負載可分離的中等電流升壓穩壓器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4861CS-3 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Low Voltage Boost Regulator |
| ML4861CS-5 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Low Voltage Boost Regulator |
| ML4861CS6 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ML4861CS-6 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Low Voltage Boost Regulator |
| ML4861ES-3 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Low Voltage Boost Regulator |
發布緊急采購，3分鐘左右您將得到回復。