參數資料
型號: MK712RLF
廠商: IDT, Integrated Device Technology Inc
文件頁數: 19/21頁
文件大?。?/td> 0K
描述: IC TOUCH SCREEN CTLR 28-SSOP
標準包裝: 48
類型: 電阻
觸摸面板接口: 4 線
輸入數/鍵: 1 TSC
分辨率(位): 12 b
數據接口: 并聯
電源電壓: 3 V ~ 5.5 V
電流 - 電源: 5mA
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 28-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 28-QSOP
包裝: 管件
MK712
TOUCH SCREEN CONTROLLER
TOUCH SCREEN CONTROL
IDT TOUCH SCREEN CONTROLLER
7
MK712
REV N 051310
Optimizing Performance when Reading and Writing Registers
Reading and writing the MK712 generates digital noise that may reduce the accuracy of the A to D converter. This
noise has several causes, including board layout, data bus loading, and power supply voltage. By appropriately
timing the register operations, the effects of this noise can be minimized.
After an interrupt is issued, the MK712 allows a minimum of 1 millisecond to elapse before initiating the conversion
cycle. This allows the screen drivers to settle. For best performance, complete all register operations within this 1ms
window after an interrupt.
Power Down/Stopping the Clock
If the screen is untouched, the supply current is under 3A. If the input clock is stopped, the supply current is also
less than 3A. When the screen is touched with no clock, TOUCH goes low and INT goes high, but no further
operations occur until the clock starts. A to D conversions are invalid until after the clock has stabilized at the correct
frequency and one full conversion cycle has been completed.
Input Clock
The MK712 is highly tolerant of different clock frequencies (from 12 to 20 MHz), rise times, and duty cycles.
However, any input clock undershoot or overshoot will cause the MK712 to draw extra current. This can be
eliminated by using a MicroClock clock synthesizer and properly terminating the clock driver. MicroClock makes low
power clock synthesizers with 14.3 MHz power down.
Resistive Touch Screen (4-wire)
Resistive touch screens consist of 2 resistive plates that are separated by a small gap. Each plate has an electrode
at each end and when the screen is touched, the two plates are shorted together at that point.
If a voltage is applied, for example, between XL and XH, then a voltage divider is formed on the X PLATE. When the
Y PLATE is touched to the X PLATE, a voltage will be developed on the Y PLATE that is proportional to distance of
the touch from XL and XH. By accurately measuring this voltage, the position of the touch can be determined.
相關PDF資料
PDF描述
MK74CB218BRLFTR IC CLK BUFFER 1:8 200MHZ 28-SSOP
MK74CB218RLFTR IC CLK BUFFER 1:8 200MHZ 28-SSOP
MM74HC00N IC GATE NAND QUAD 2INPUT 14-DIP
MM74HC02SJX IC GATE NOR QUAD 2-INP 14-SOP
MM74HC04N IC INVERTER HEX 14-DIP
相關代理商/技術參數
參數描述
MK712RLFTR 功能描述:IC TOUCH SCREEN CTLR 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
MK712RTR 功能描述:IC TOUCH SCREEN CTLR 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
MK712RWLF 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:TOUCH SCREEN CONTROLLER
MK712RWLFTR 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:TOUCH SCREEN CONTROLLER
MK712S 功能描述:IC TOUCH SCREEN CTLR 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)