- 您現在的位置：買賣IC網 > PDF目錄26831 > MK3805SI (INTEGRATED DEVICE TECHNOLOGY INC) LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 PDF資料下載
參數資料
| 型號： | MK3805SI |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘及定時 |
| 英文描述： | LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| 封裝： | 0.300 INCH, SOIC-20 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 210K |
| 代理商： | MK3805SI |
Buffer/Clock Driver
MDS 3805 A
3
Revision 072203
Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ●
www.icst.com
MK3805
Preliminary Information
External Components
The MK3805 requires a minimum number of external
components for proper operation.
Decoupling Capacitors
Decoupling capacitors of 0.01F must be connected
between VDD and GND, as close to these pins as
possible. For optimum device performance, the
decoupling capacitors should be mounted on the
component side of the PCB. Avoid the use of vias in the
decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be
used. To series terminate a 50
trace (a commonly
used trace impedance) place a 33
resistor in series
with the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20
.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) The 0.01F decoupling capacitors should be
mounted on the component side of the board as close
to the VDD pins as possible. No vias should be used
between the decoupling capacitors and VDD pins. The
PCB trace to VDD pin should be kept as short as
possible, as should the PCB trace to the ground via.
2) To minimize EMI the 33
series termination resistor,
if needed, should be placed close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through the
signal layers. Other signal traces should be routed
away from the MK3805. This includes signal traces just
underneath the device, or on layers adjacent to the
ground plane layer used by the device.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK3805. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Item
Rating
Supply Voltage, VDD
7V
All Inputs and Outputs
-0.5V to VDD+0.5V
Ambient Operating Temperature
-40 to +85
°C
Storage Temperature
-65 to +150
°C
Junction Temperature
175
°C
Soldering Temperature
260
°C
相關PDF資料 |
PDF描述 |
|---|---|
| MK3805SIT | LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| MK3805SILF | LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| MK3807-01GIT | 3807 SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| MK3807-01SIT | 3807 SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| MK3807-01RIT | 3807 SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK3807-01 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:BUFFER/CLOCK DRIVER |
| MK3807-01RI | 功能描述:IC CLK BUFF 1:10 100MHZ 20-QSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:- 標準包裝:1 系列:HiPerClockS™ 類型:扇出緩沖器（分配），多路復用器 電路數:1 比率 - 輸入:輸出:2:18 差分 - 輸入:輸出:是/無 輸入:CML，LVCMOS，LVPECL，LVTTL，SSTL 輸出:LVCMOS，LVTTL 頻率 - 最大:250MHz 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:- 其它名稱:800-1923-6 |
| MK3807-01RILF | 功能描述:時鐘驅動器及分配 BUFFER/CLOCK DRIVER RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| MK3807-01RILFTR | 功能描述:時鐘驅動器及分配 BUFFER/CLOCK DRIVER RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| MK3807-01RITR | 功能描述:IC CLK BUFF 1:10 100MHZ 20-QSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:- 標準包裝:1 系列:HiPerClockS™ 類型:扇出緩沖器（分配），多路復用器 電路數:1 比率 - 輸入:輸出:2:18 差分 - 輸入:輸出:是/無 輸入:CML，LVCMOS，LVPECL，LVTTL，SSTL 輸出:LVCMOS，LVTTL 頻率 - 最大:250MHz 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:- 其它名稱:800-1923-6 |
發布緊急采購，3分鐘左右您將得到回復。