- 您現在的位置：買賣IC網 > PDF目錄39599 > MK1707DTR (INTEGRATED DEVICE TECHNOLOGY INC) 108 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF資料下載
參數資料
| 型號： | MK1707DTR |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 108 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 3/7頁 |
| 文件大小： | 177K |
| 代理商： | MK1707DTR |
MK1707D
LOW EMI CLOCK GENERATOR
SSCG
IDT / ICS LOW EMI CLOCK GENERATOR
3
MK1707D
REV F 102804
External Components
The MK1707D requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01F must be connected
between VDD and GND on pins 2 and 3, as close to these
pins as possible. For optimum device performance, the
decoupling capacitor should be mounted on the component
side of the PCB. Avoid the use of vias in the decoupling
circuit.
Series Termination Resistor
When the PCB trace between the clock output and the load
is over 1 inch, series termination should be used. To series
terminate a 50
trace (a commonly used trace impedance),
place a 33
resistor in series with the clock line, as close to
the clock output pin as possible. The nominal impedance of
the clock output is 20
.
Select Pin Operation
The S1, S0 select pins are 2-level, meaning they have three
separate states to make the selections shown in the table on
page 2.
PCB layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
1) The 0.01F decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No vias should be used between the decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
be kept as short as possible, as should the PCB trace to the
ground via.
2) To minimize EMI, the 33
series termination resistor (if
needed) should be placed close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers. Other signal traces should be routed away from the
MK1707D. This includes signal traces just underneath the
device, or on layers adjacent to the ground plane layer used
by the device.
.
相關PDF資料 |
PDF描述 |
|---|---|
| MK1714-01RILF | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| MK1714-02RLFT | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| MK1714-02RT | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| MK1714-02RLFT | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| MK1714-02RLF | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK1707S | 功能描述:IC CLK GENERATOR LOW EMI 8-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| MK1707SI | 功能描述:IC CLK GENERATOR LOW EMI 8-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MK1707SILF | 功能描述:時鐘發生器及支持產品 LOW EMI CLOCK GENERATOR RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MK1707SILFTR | 功能描述:時鐘發生器及支持產品 LOW EMI CLOCK GENERATOR RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MK1707SITR | 功能描述:IC CLK GENERATOR LOW EMI 8-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。