- 您現在的位置：買賣IC網 > PDF目錄5382 > MIC913BM5 TR (Micrel Inc)IC OPAMP 350MHZ HS LP SOT23-5 PDF資料下載
參數資料
| 型號： | MIC913BM5 TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 4/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP 350MHZ HS LP SOT23-5 |
| 標準包裝： | 3,000 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 1 |
| 轉換速率： | 500 V/µs |
| 增益帶寬積： | 350MHz |
| -3db帶寬： | 240MHz |
| 電流 - 輸入偏壓： | 5.5µA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 4.2mA |
| 電流 - 輸出 / 通道： | 90mA |
| 電壓 - 電源，單路/雙路(±)： | ±2.5 V ~ 9 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC913BM5TR MIC913BM5TR-ND |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
Micrel, Inc.
MIC913
October 2007
12
M9999-101707
Application Information
The MIC913 is a high-speed, voltage-feedback opera-
tional amplifier featuring very low supply current. The
MIC913 is not unity-gain stable, it requires a minimum
gain of +2 or –1 to ensure stability. The device is
however stable even when driving high capacitance
loads.
Driving High Capacitance
The MIC913 is stable when driving any capacitance (see
“Typical Characteristics: Gain Bandwidth and Phase
Margin vs. Load Capacitance”) making it ideal for driving
long coaxial cables or other high-capacitance loads.
Phase margin remains constant as load capacitance is
increased. Most high-speed op amps are only able to
drive limited capacitance.
Note: increasing load capacitance does reduce
the speed of the device (see “Typical Character-
istics: Gain Bandwidth and Phase Margin vs.
Load”). In applications where the load capaci-
tance reduces the speed of the op amp to an
unacceptable level, the effect of the load capaci-
tance can be reduced by adding a small resistor
(<100) in series with the output.
Feedback Resistor Selection
Conventional op amp gain configurations and resistor
selection apply, the MIC913 is NOT a current feedback
device. Resistor values in the range of 1k to 10k are
recommended.
Layout Considerations
All high speed devices require careful PCB layout. The
high stability and high PSRR of the MIC913 make this op
amp easier to use than most, but the following guidelines
should be observed: Capacitance, particularly on the two
inputs pins will degrade performance; avoid large copper
traces to the inputs. Keep the output signal away from
the inputs and use a ground plane.
It is important to ensure adequate supply bypassing
capacitors are located close to the device.
Power Supply Bypassing
Regular supply bypassing techniques are recom-
mended. A 10F capacitor in parallel with a 0.1F
capacitor on both the positive and negative supplies are
ideal. For best performance all bypassing capacitors
should be located as close to the op amp as possible
and all capacitors should be low ESL (equivalent series
inductance),
ESR
(equivalent
series
resistance).
Surface-mount ceramic capacitors are ideal.
Thermal Considerations
The SOT-23-5 package, like all small packages, has a
high thermal resistance. It is important to ensure the IC
does not exceed the maximum operating junction (die)
temperature of 85°C. The part can be operated up to the
absolute maximum temperature rating of 125°C, but
between 85°C and 125°C performance will degrade, in
particular CMRR will reduce.
A MIC913 with no load, dissipates power equal to the
quiescent supply current * supply voltage.
PD(no load) = (VV+ – VV–)IS
When a load is added, the additional power is dissipated
in the output stage of the op amp. The power dissipated
in the device is a function of supply voltage, output
voltage and output current.
PD(output stage) = (VV+ – VV–)IOUT
Total Power Dissipation = PD(no load) + PD(output stage)
Ensure the total power dissipated in the device is no
greater than the thermal capacity of the package. The
SOT23-5 package has a thermal resistance of 260°C/W.
260W
T
n
Dissipatio
Power
Allowable
Max.
A(max)
J(max)
=
相關PDF資料 |
PDF描述 |
|---|---|
| 1SMA36CAT3 | TVS 400W 36V BIDIRECT SMA |
| 5535676-5 | CONN RECEPT 6POS .100 RT/ANG AU |
| 1SMA6.5AT3 | TVS 400W 6.5V UNIDIRECT SMA |
| 535676-5 | CONN RECEPT 6POS .100 RT/ANG AU |
| 94860 | TERM RING 22-18AWG HS INSUL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC913YM5 TR | 功能描述:運算放大器 - 運放 350MHz, 4.2mA High Speed Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MIC913YM5-TR | 功能描述:Voltage Feedback Amplifier 1 Circuit SOT-23-5 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:Last Time Buy 放大器類型:電壓反饋 電路數:1 輸出類型:- 壓擺率:500 V/μs 增益帶寬積:350MHz -3db 帶寬:240MHz 電流 - 輸入偏置:5.5μA 電壓 - 輸入失調:1mV 電流 - 電源:4.2mA 電流 - 輸出/通道:90mA 電壓 - 電源，單/雙（±）:±2.5 V ~ 9 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商器件封裝:SOT-23-5 標準包裝:1 |
| MIC914 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:160MHz Low-Power SOT-23-5 Op Amp |
| MIC914_07 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:160MHz Low-Power SOT23-5 Op Amp |
| MIC914BM5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。