- 您現在的位置：買賣IC網 > Datasheet目錄45 > MIC5191BMM TR (Micrel Inc)IC REG CTRLR SGL POS ADJ 10-MSOP Datasheet資料下載
參數資料
| 型號： | MIC5191BMM TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 845K |
| 描述： | IC REG CTRLR SGL POS ADJ 10-MSOP |
| 標準包裝： | 2,500 |
| 類型： | 正，可調式 |
| 輸出數： | 1 |
| 輸出電壓： | 可調 |
| 電流 - 電源： | 15mA |
| 輸入電壓： | 1 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC5191BMMTR MIC5191BMMTR-ND |
Micrel, Inc.
MIC5191
December 2006
7
M9999-122206
Functional Description
VIN
The VIN pin is connected to the N-Channel drain. VIN is
the input power being supplied to the output. This pin is
also used to power the internal current limit comparator
and compare the ISENSE voltage for current limit. The
voltage range is from 1.0V min to 5.5V max.
ISENSE
The ISENSE pin is the other input to the current limit
comparator. The output current is limited when the
ISENSE pin's voltage is 50mV less than the VIN pin. In
cases where there is a current limited source and there
isnt a need for current limit, this pin can be tied directly
to VIN. Its operating voltage range, like the VIN pin, is
1.0V min to 5.5V max.
VCC1, VCC2
VCC1 supplies the error amplifier and internal reference,
while VCC2 supplies the output gate drive. For this
reason, ensure these pins have good input capacitor
bypassing for better performance. The operating range
is from 4.5V to 13.2V and both VCC pins should be tied
together. Ensure that the voltage supplied is greater than
a gate-source threshold above the output voltage for the
N-Channel MOSFET selected.
Output
The output drives the external N-Channel MOSFET and
is powered from VCC. The output can sink and source
over 150mA of current to drive either an N-Channel
MOSFET or an external NPN transistor. The output drive
also has short-circuit current protection.
Enable
The MIC5191 comes with an active-high enable pin that
allows the regulator to be disabled. Forcing the enable
pin low disables the regulator and sends it into a low off-
mode-current state. Forcing the enable pin high enables
the output voltage. The enable pin cannot be left floating;
a floating enable pin may cause an indeterminate state
on the output.
FB
The feedback pin is used to sense the output voltage for
regulation. The feedback pin is compared to an internal
1.0V reference and the output adjusts the gate voltage
accordingly to maintain regulation. Since the feedback
biasing current is typically 13礎, smaller feedback
resistors should be used to minimize output voltage
error.
COMP
COMP is the external compensation pin. This allows
complete control over the loop to allow stability for any
type of output capacitor, load currents and output
voltage. A detailed explanation of how to compensate
the MIC5191 is in the Designing with the MIC5191
section.
SGND, PGND
SGND is the internal signal ground which provides an
isolated ground path from the high current output driver.
The signal ground provides the grounding for noise
sensitive circuits such as the current limit comparator,
error amplifier and the internal reference voltage.
PGND is the power ground and is the grounding path for
the output driver.
相關PDF資料 |
PDF描述 |
|---|---|
| ML4800CP | IC PFC CTRLR AVERAGE CURR 16DIP |
| ML4824CS2 | IC PFC PWM CTRLR COMBO 16-SOIC |
| MX536AJCWE+ | IC CONV TRUE RMS-DC 2MHZ 16SOIC |
| MX884HTTR | IC CURRENT MONITOR TSOT23-6 |
| NCP1080DEG | IC CONV CTLR POE-PD 13W 20-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC5191YML | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Ultra High-Speed, High-Current Active Filter / LDO Controller |
| MIC5191YML TR | 功能描述:低壓差控制器 - LDO Ultra Hi-Speed Hi-Current Active Filter/LDO Controller(Lead Free) RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節: 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6 |
| MIC5191YML-TR | 功能描述:Linear Regulator Controller IC Positive Adjustable 1 Output 10-MLF? (3x3) 制造商:microchip technology 系列:- 包裝:* 零件狀態:停產 類型:正，可調式 輸出數:1 電流 - 電源:15mA 電壓 - 輸入:1 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:10-VFDFN 裸露焊盤，10-MLF? 供應商器件封裝:10-MLF?（3x3） 標準包裝:1 |
| MIC5191YMM | 功能描述:低壓差控制器 - LDO Ultra Hi-Speed Hi-Current Active Filter/LDO Controller(Lead Free) RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節: 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6 |
| MIC5191YMM TR | 功能描述:低壓差控制器 - LDO Ultra Hi-Speed Hi-Current Active Filter/LDO Controller(Lead Free) RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節: 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6 |
發布緊急采購，3分鐘左右您將得到回復。