- 您現在的位置：買賣IC網 > PDF目錄384734 > MIC2199 (Micrel Semiconductor,Inc.) 300kHz 4mm 】 4mm Synchronous Buck Converter PDF資料下載
參數資料
| 型號： | MIC2199 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | 300kHz 4mm 】 4mm Synchronous Buck Converter |
| 中文描述： | 300kHz的4毫米】4mm的同步降壓轉換器 |
| 文件頁數： | 14/15頁 |
| 文件大小： | 222K |
| 代理商： | MIC2199 |
MIC2199
Micrel
MIC2199
14
November 2004
Decoupling Capacitor Selection
The 4.7
μ
F decoupling capacitor is used to minimize noise on
the V
DD
pin. The placement of this capacitor is critical to the
proper operation of the IC. It must be placed right next to the
pins and routed with a wide trace. The capacitor should be a
good quality tantalum. An additional 1
μ
F ceramic capacitor
may be necessary when driving large MOSFETs with high
gate capacitance. Incorrect placement of the V
DD
decoupling
capacitor will cause jitter or oscillations in the switching
waveform and large variations in the overcurrent limit.
A 0.1
μ
F ceramic capacitor is required to decouple the V
IN
.
The capacitor should be placed near the IC and connected
directly to between pin 6 (V
IN
) and pin 9 (GND).
PCB Layout and Checklist
PCB layout is critical to achieve reliable, stable and efficient
performance. A ground plane is required to control EMI and
minimize the inductance in power, signal and return paths.
The following guidelines should be followed to insure proper
operation of the circuit.
Signal and power grounds should be kept separate
and connected at only one location. Large currents
or high di/dt signals that occur when the MOSFETs
turn on and off must be kept away from the small
signal connections.
The connection between the current-sense resis-
tor and the MIC2199 current-sense inputs (pin 4
and 5) should have separate traces, through a 10
resistor on each pin. The traces should be routed
as closely as possible to each other and their
length should be minimized. Avoid running the
traces under the inductor and other switching
components. The 10
resistor should be placed
close as possible to pins 4 and 5 on the MIC2199
and a 1nF to 0.1
μ
F capacitor placed between pins
4 and 5 will help attenuate switching noise on the
current sense traces. This capacitor should be
placed close to pins 4 and 5.
When the high-side MOSFET is switched on, the
critical flow of current is from the input capacitor
through the MOSFET, inductor, sense resistor,
output capacitor, and back to the input capacitor.
These paths must be made with short, wide pieces
of trace. It is good practice to locate the ground
terminals of the input and output capacitors close
to each.
When the low-side MOSFET is switched on, cur-
rent flows through the inductor, sense resistor,
output capacitor, and MOSFET. The source of the
low-side MOSFET should be located close to the
output capacitor.
The freewheeling diode, D1 in Figure 2, conducts
current during the dead time, when both MOSFETs
are off. The anode of the diode should be located
close to the output capacitor ground terminal and
the cathode should be located close to the input
side of the inductor.
The 4.7
μ
F capacitor, which connects to the V
DD
terminal (pin 7) must be located right at the IC. The
V
DD
terminal is very noise sensitive and placement
of this capacitor is very critical. Connections must
be made with wide trace. The capacitor may be
located on the bottom layer of the board and
connected to the IC with multiple vias.
The V
IN
bypass capacitor should be located close
to the IC and connected between pins 6 and 9.
Connections should be made with a ground and
power plane or with short, wide trace.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2199BML | 300kHz 4mm 】 4mm Synchronous Buck Converter |
| MIC2206 | 2MHz PWM Synchronous Buck Regulator with LOWQ Mode and Voltage Scaling |
| MIC2207YML | 3mmx3mm 2MHz 3A PWM Buck Regulator |
| MIC2207 | 3mmx3mm 2MHz 3A PWM Buck Regulator |
| MIC2213 | Sequenced Portable Power Management IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2199_10 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:300kHz 4mm × 4mm Synchronous Buck Converter |
| MIC2199BML | 功能描述:IC REG CTRLR BUCK PWM CM 12-MLF RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| MIC2199BML TR | 功能描述:IC REG CTRLR BUCK PWM CM 12-MLF RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| MIC2199YML | 功能描述:DC/DC 開關控制器 300KHz 12 Lead Sync Buck Controller - Lead Free RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MIC2199YML EV | 功能描述:電源管理IC開發工具 300KHz 12 Lead Sync Buck Controller - Evaluation Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。