- 您現在的位置：買賣IC網 > PDF目錄2013 > MIC1555BM5 TR (Micrel Inc)IC OSC MONO TIMING 5MHZ SOT23-5 PDF資料下載
參數資料
| 型號： | MIC1555BM5 TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OSC MONO TIMING 5MHZ SOT23-5 |
| 標準包裝： | 3,000 |
| 系列： | IttyBitty® |
| 類型： | 555 型，計時器/振蕩器（單路） |
| 頻率： | 5MHz |
| 電源電壓： | 2.7 V ~ 18 V |
| 電流 - 電源： | 350µA |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | SC-74A，SOT-753 |
| 包裝： | 帶卷 (TR) |
| 供應商設備封裝： | SOT-23-5 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | MIC1555BM5TR MIC1555BM5TR-ND |
Micrel, Inc.
MIC1555/1557
March 11, 2014
11
Revision 6.0
Application Information
Basic Monostable (One-Shot) Circuit
A monostable oscillator produces a single pulse each
time that it is triggered, and is often referred to as a “one-
shot”. The pulse width is constant, while the time
between pulses depends on the trigger input. One-shots
are generally used to “stretch” incoming pulses, of
varying widths, to a fixed width. The IttyBitty MIC1555 is
designed for monostable operation, but may also be
connected to provide astable oscillations. The pulse width
is determined by the time it takes to charge a capacitor
from ground to a comparator trip point. If the capacitor
(CT) is charged through a resistor (RT) connected to the
output of an MIC1555, the trip point is approximately
1.1RTCT (the same time as the initial power-on cycle of
an astable circuit.) If the trigger pulse of an MIC1555
remains low longer than the output pulse width, short
oscillations may be seen in the output of a one-shot
circuit, since the threshold pin has precedence over the
trigger pin. These occur since the output goes low when
the threshold is exceeded, and then goes high again as
the trigger function is asserted. AC coupling the input with
a series capacitor and a pull-up resistor, with an RC time
constant less than the pulse width, will prevent these
short oscillations. A diode (DT) in parallel with (RT) resets
the one-shot quickly.
Figure 1. One-Shot Diagram
The period of a monostable circuit is:
t = k2 RC
where:
t = period (s)
R = Resistance ()
C = Capacitance (F)
Basic Astable (Oscillator) Circuits
An astable oscillator switches between two states, “on”
and “off”, producing a continuous square wave. The
IttyBitty MIC1557 is optimized for this function, with the
two comparator inputs, threshold and trigger (T/T), tied
together internally. CS is brought out to allow on-off
control of the oscillator.
The MIC1555 may also be used as an astable oscillator
by tying the threshold and trigger pins together, forming a
T/T pin. If a resistor (RT) is connected from the output to a
grounded timing capacitor (CT), the voltage at their
junction will ramp up from ground when the output goes
high. If the T/T pin is connected to this junction, the
output will switch low when the ramp exceeds 2/3 of the
input voltage. The junction's voltage ramps down toward
ground while the output is low. When the ramp is below
1/3 of the input voltage, the output switches to high, and
the junction ramps up again. The continuing frequency of
an MIC1555/7 astable oscillator depends on the RC time
constant, and is approximately 0.7/RC below 1MHz. At
frequencies above 1MHz the RC multiplier increases as
capacitance
is
decreased,
and
propagation
delay
becomes dominant. Non-symmetrical oscillator operation
is possible at frequencies up to 5MHz.
If a duty cycle other than 50% is desired, a low-power
signal diode may be connected in series with the timing
resistor (RA), and a second resistor (RB) in series with an
opposite facing switching diode and resistor connected in
parallel (see Figure 2). The frequency is then made up of
two
components,
the
charging
time
(tA) and the
discharging time (tB) tA = 0.7RACT and tB = 0.7RBCT. The
frequency is the reciprocal of the sum of the two times tA
+ tB, so the total time is 1.4RTCT. The first half-cycle of an
astable, after power-on or CS enable, is lengthened since
the capacitor is charging from ground instead of the 1/3
input trigger trip voltage, to 1.1RC, the same as a
monostable pulse.
相關PDF資料 |
PDF描述 |
|---|---|
| MK1491-09FTR | IC CLK SRC AMD GEODE GX2 28-SSOP |
| MK1574-01BSILF | IC PLL FRAME RATE COMM 16-SOIC |
| MK1575-01GILF | IC CLK RECOVERY PLL 16-TSSOP |
| MK1704ALF | IC CLK GENERATOR LOW EMI 8-SOIC |
| MK1705ALF | IC CLK GEN ATI LOW EMI 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC1555YM5 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:IttyBitty RC Timer / Oscillator |
| MIC1555YM5 TR | 功能描述:計時器和支持產品 2.7V to 18V, "555" RC Timer/Oscillator with Trigger Input in SOT23-5 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MIC1555YM5TR | 制造商:Micrel 功能描述:Standard Timer Single, Oscillator 5MHz |
| MIC1555YM5-TR | 功能描述:555 Type, Timer/Oscillator (Single) IC 5MHz SC-74A, SOT-753 制造商:microchip technology 系列:IttyBitty? 包裝:剪切帶（CT） 零件狀態:有效 類型:555 型，計時器/振蕩器（單路） 計數:- 頻率:5MHz 電壓 - 電源:2.7 V ~ 18 V 電流 - 電源:350μA 工作溫度:-40°C ~ 85°C 封裝/外殼:SC-74A，SOT-753 供應商器件封裝:SOT-23-5 安裝類型:表面貼裝 標準包裝:1 |
| MIC1555YMU-T5 | 功能描述:555 Type, Timer/Oscillator (Single) IC 5MHz 10-XFDFN Exposed Pad 制造商:microchip technology 系列:IttyBitty? 包裝:剪切帶（CT） 零件狀態:停產 類型:555 型，計時器/振蕩器（單路） 計數:- 頻率:5MHz 電壓 - 電源:2.7 V ~ 18 V 電流 - 電源:350μA 工作溫度:-40°C ~ 85°C 封裝/外殼:10-XFDFN 裸露焊盤 供應商器件封裝:10-UTDFN（2x2） 安裝類型:表面貼裝 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。