參數資料
型號： MEGA32C1-ESAZ
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP32
封裝： 7 X 7 MM, 1 MM HEIGHT, 0.50 MM PITCH, LEAD FREE, PLASTIC, TQFP-32
文件頁數： 1/95頁
文件大小： 6074K
代理商： MEGA32C1-ESAZ
158
ATtiny25/45/85 [DATASHEET]
2586Q–AVR–08/2013
20.7.5
Programming the EEPROM
The EEPROM is organized in pages, see Table 21-11 on page 170. When programming the EEPROM, the data is
latched into a page buffer. This allows one page of data to be programmed simultaneously. The programming algo-
rithm for the EEPROM Data memory is as follows (refer to Table 20-16):
1.
Load Command “Write EEPROM”.
2.
Load EEPROM Page Buffer.
3.
Program EEPROM Page. Wait after Instr. 2 until SDO goes high for the “Page Programming” cycle to
finish.
4.
Repeat 2 through 3 until the entire EEPROM is programmed or until all data has been programmed.
5.
End Page Programming by Loading Command “No Operation”.
20.7.6
Reading the Flash
The algorithm for reading the Flash memory is as follows (refer to Table 20-16):
1.
Load Command "Read Flash".
2.
Read Flash Low and High Bytes. The contents at the selected address are available at serial output SDO.
20.7.7
Reading the EEPROM
The algorithm for reading the EEPROM memory is as follows (refer to Table 20-16):
1.
Load Command “Read EEPROM”.
2.
Read EEPROM Byte. The contents at the selected address are available at serial output SDO.
20.7.8
Programming and Reading the Fuse and Lock Bits
The algorithms for programming and reading the Fuse Low/High bits and Lock bits are shown in Table 20-16.
20.7.9
Reading the Signature Bytes and Calibration Byte
The algorithms for reading the Signature bytes and Calibration byte are shown in Table 20-16.
20.7.10
Power-off sequence
Set SCI to “0”. Set RESET to “1”. Turn V
CC power off.
Table 20-16. High-voltage Serial Programming Instruction Set for ATtiny25/45/85
Instruction
Instruction Format
Operation Remarks
Instr.1/5
Instr.2/6
Instr.3
Instr.4
Chip Erase
SDI
SII
SDO
0_1000_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Wait after Instr.3 until SDO
goes high for the Chip Erase
cycle to finish.
Load “Write
Flash”
Command
SDI
SII
SDO
0_0001_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
Enter Flash Programming
code.
Load Flash
Page Buffer
SDI
SII
SDO
0_bbbb_bbbb _00
0_0000_1100_00
x_xxxx_xxxx_xx
0_eeee_eeee_00
0_0010_1100_00
x_xxxx_xxxx_xx
0_dddd_dddd_00
0_0011_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1101_00
x_xxxx_xxxx_xx
Repeat after Instr. 1 - 5 until
the entire page buffer is filled
or until all data within the
page is filled.
SDI
SII
SDO
0_0000_0000_00
0_0111_1100_00
x_xxxx_xxxx_xx
Instr 5.
相關PDF資料
PDF描述
MEGA32C1-ESMZ 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, QCC32
MFR4300MAE40 2 CHANNEL(S), 10M bps, SERIAL COMM CONTROLLER, PQFP64
MG80C18612883B 16-BIT, 12.5 MHz, MICROPROCESSOR, CPGA68
MG80C186-10 16-BIT, 10 MHz, MICROPROCESSOR, CPGA68
MQ80C186-12 16-BIT, 12.5 MHz, MICROPROCESSOR, CQFP68
相關代理商/技術參數
參數描述
MEGA32C1-ESMZ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K/64K Bytes In-System Programmable Flash
MEGA32M1-15AZ 制造商:Atmel Corporation 功能描述:
MEGA32M1-15MZ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K/64K Bytes In-System Programmable Flash
MEGA32M1-ESAZ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K/64K Bytes In-System Programmable Flash
MEGA32M1-ESMZ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K/64K Bytes In-System Programmable Flash
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*