- 您現在的位置：買賣IC網 > PDF目錄45265 > MD80C32-30 (ATMEL CORP) 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MD80C32-30 |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | CERAMIC, DIP-40 |
| 文件頁數： | 243/586頁 |
| 文件大?。?/td> | 25028K |
| 代理商： | MD80C32-30 |
317
8272E–AVR–04/2013
ATmega164A/PA/324A/PA/644A/PA/1284/P
27.9.1
Serial Programming Characteristics
For characteristics of the Serial Programming module see “SPI timing characteristics” on page
Figure 27-12. Serial programming waveforms.
27.10 Programming via the JTAG Interface
Programming through the JTAG interface requires control of the four JTAG specific pins: TCK,
TMS, TDI, and TDO. Control of the reset and clock pins is not required.
To be able to use the JTAG interface, the JTAGEN Fuse must be programmed. The device is
default shipped with the fuse programmed. In addition, the JTD bit in MCUCR must be cleared.
Alternatively, if the JTD bit is set, the external reset can be forced low. Then, the JTD bit will be
cleared after two chip clocks, and the JTAG pins are available for programming. This provides a
means of using the JTAG pins as normal port pins in Running mode while still allowing In-Sys-
tem Programming via the JTAG interface. Note that this technique can not be used when using
the JTAG pins for Boundary-scan or On-chip Debug. In these cases the JTAG pins must be ded-
icated for this purpose.
During programming the clock frequency of the TCK Input must be less than the maximum fre-
quency of the chip. The System Clock Prescaler can not be used to divide the TCK Clock Input
into a sufficiently low frequency.
As a definition in this datasheet, the LSB is shifted in and out first of all Shift Registers.
27.10.1
Programming Specific JTAG Instructions
The Instruction Register is 4-bit wide, supporting up to 16 instructions. The JTAG instructions
useful for programming are listed below.
The OPCODE for each instruction is shown behind the instruction name in hex format. The text
describes which Data Register is selected as path between TDI and TDO for each instruction.
The Run-Test/Idle state of the TAP controller is used to generate internal clocks. It can also be
used as an idle state between JTAG sequences. The state machine sequence for changing the
instruction word is shown in Figure 27-13 on page 318.
MSB
LSB
SERIAL CLOCK INPUT
(SCK)
SERIAL DATA INPUT
(MOSI)
(MISO)
SAMPLE
SERIAL DATA OUTPUT
相關PDF資料 |
PDF描述 |
|---|---|
| MD80C32E-30/883 | 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 |
| MD80C52CXXX-30/883 | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CDIP40 |
| MR80C52EXXX-16/883 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44 |
| MR80C52TXXX-36/883 | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQCC44 |
| MD80C32-12/883:D | 8-BIT, 12 MHz, MICROCONTROLLER, CDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MD80C51 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 44 MHz Single-Chip 8 Bit Microcontroller |
| MD80C51BH | 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space |
| MD80C51FB | 制造商:Rochester Electronics LLC 功能描述: |
| MD80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C862 | 制造商:Intel 功能描述:PROCESSOR:MICRO-PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。