- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33927EK (飛思卡爾半導體(中國)有限公司) Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod PDF資料下載
參數資料
| 型號： | MCZ33927EK |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod |
| 中文描述： | 三相場效應晶體管預驅動器 |
| 文件頁數： | 21/44頁 |
| 文件大?。?/td> | 490K |
| 代理商： | MCZ33927EK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33927
FUNCTIONAL DESCRIPTIONS
INTRODUCTION
reference for the SPI port. A 0.47μF (min) decoupling
capacitor must be connected to this pin.
This regulator is intended for internal IC use and can
supply only a small (1mA) external load current.
A power-on-reset (POR) circuit monitors this pin and until
the voltage rises above the threshold, the internal logic will be
reset; driver outputs will be tri-stated and SPI communication
disabled.
The VDD regulator can be disabled by asserting the RST
signal low. The VDD regulator is powered from the VPWR
pin.
PHASE B HIGH-SIDE CONTROL INPUT (PB_HS)
This pin is the input logic signal, enabling the High-Side
driver for Phase B. The signal is active low, and is pulled up
by an internal current source.
PHASE B LOW-SIDE INPUT (PB_LS)
This pin is the input logic signal, enabling the Low-Side
driver for Phase B. The signal is active high, and is pulled
down by an internal current sink.
INTERRUPT (INT)
The Interrupt pin is a totem pole logic output. When a fault
is detected, this pin will pull high until it is cleared by
executing the Clear Interrupt command via the SPI port. The
faults capable of causing an interrupt can be masked via the
MASK0 and MASK1 SPI registers to customize the
response.
CHIP SELECT (CS)
Chip select is a logic input that frames the SPI commands
and enables the SPI port. This signal is active low, and is
pulled up by an internal current source.
SERIAL IN (SI)
The Serial In pin is used to input data to the SPI port.
Clocked on the falling edge of SCLK, it is the most significant
bit (MSB) first. This pin is pulled down by an internal current
sink.
SERIAL CLOCK (SCLK)
This logic input is the clock is used for the SPI port. The
SCLK typically runs at 3 MHz (up to 5 MHz) and is pulled
down by an internal current sink.
SERIAL OUT (SO)
Output data for the SPI port streams from this pin. It is tri-
stated until CS is low. New data appears on rising edges of
SCLK in preparation for latching by the falling edge of SCLK
on the master.
PHASE C LOW-SIDE INPUT (PC_LS)
This input logic pin enables the Low-Side Driver for Phase
C. This pin is an active high, and is pulled down by an internal
current sink.
PHASE C HIGH-SIDE INPUT (PC_HS)
This input logic pin enables the High-Side Driver for Phase
C. This signal is active low, and is pulled up by an internal
current source.
AMPLIFIER OUTPUT (AMP_OUT)
This pin is the output for the current sensing amplifier. It is
also the sense input to the overcurrent comparator.
AMPLIFIER INVERTING INPUT (AMP_N)
The inverting input to the current sensing amplifier.
AMPLIFIER NON-INVERTING INPUT (AMP_P)
The non-inverting input to the current sensing amplifier.
OVERCURRENT COMPARATOR OUTPUT
(OC_OUT)
The overcurrent comparator output is a totem pole logic
level output. A logic high indicates an overcurrent condition.
OVERCURRENT COMPARATOR THRESHOLD
(OC_TH)
This input sets the threshold level of the overcurrent
comparator.
VOLTAGE SOURCE SUPPLY (VSS)
VSS is the ground reference for the logic interface and
power supplies.
GROUND (GND0,GND1)
These two pins are connected internally to VSS by a 1.0
resistor. They provide device substrate connections and also
the primary return path for ESD protection.
VLS REGULATOR CAPACITOR (VLS_CAP)
This connection is for a capacitor which will provide a low
impedance for switching currents on the gate drive. A low
ESR decoupling capacitor, capable of sourcing the pulsed
drive currents must be connected between this pin and VSS.
This is the same DC node as VLS, but it is physically
placed on the opposite end of the IC to minimize the source
impedance to the gate drive circuits.
PHASE C GROUND (PGNDC)
The phase C power ground is the pin used to return the
gate currents from the low side FET. Best performance is
normally realized by connecting this node directly to the
source of the low side FET for phase C.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33970EG | Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms |
| MCZ33976EG | Dual Gauge Driver with Configurable esponse Time |
| MCZ33977EG | Single Gauge Driver |
| MCZ33989EG | System Basis Chip with High-Speed CAN Transceiver |
| MCZ33990EF | Enhanced Class B Serial Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33927EK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver |
| MCZ33927EKR2 | 功能描述:功率驅動器IC THREE PHASE PRE- DRIVER RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33927R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver |
| MCZ33937AEK | 功能描述:馬達/運動/點火控制器和驅動器 3 Phase Pre-Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33937AEK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver |
發布緊急采購，3分鐘左右您將得到回復。